AMC 20-10 Acceptable Means of Compliance for the Approval of Digital ATIS via Data Link over ACARS

• ED Decision 2006/012/R found in: AMC-20 Amdt 22 - Airworthiness of Products, Parts and Appliances (May 2021)

AMC 20-10Acceptable Means of Compliance for the Approval of Digital ATIS via Data Link over ACARS ED Decision 2006/012/R 1 PREAMBLE 1.1 This AMC is issued in response to the EUROCONTROL Convergence and Implementation Plan that recommends an interim deployment of air-to-ground and ground-to-air data link applications based on the existing airline ACARS technology. One such application is Digital Automated Terminal Information Services (D-ATIS) now planned to be operational at various airports in Europe. Aircraft operators, on a voluntary basis, may take advantage of D-ATIS where it is available, provided the service is verified in accordance with operational procedures acceptable to the responsible operations authority. 1.2 The use of ACARS for data link purposes is a transitional step to data link applications that will use VHF Digital Link (VDL) Mode 2 and the Aeronautical Telecommunications Network (ATN), compliant with ICAO SARPS, as proposed in the EUROCONTROL LINK2000+ programme[[7]](#_ftn7). 1.3 Described in EUROCAE document ED-89A, Data Link Application System document (DLASD) for the “ATIS” Data Link Service, D-ATIS is a control tower application providing direct communication of ATIS information to the flight crew and, optionally automatic updating of this information. The ED-89A document addresses three domains: airborne, ground ATC, and communication service providers. It deals also with associated flight crew and air traffic service provider procedures. ED-89A incorporates the protocols and message formats formerly published in ARINC Specification 623, and takes account of EUROCAE document ED-78 which describes the global processes including approval planning, co-ordinated requirements determination, development and qualification of a system element, entry into service, and operations. 2. PURPOSE 2.1 This AMC is intended for operators intending to use Digital ATIS over ACARS as described in document EUROCAE ED-89A. It may assist also other stakeholders such as airspace planners, air traffic service providers (ATSP), ATS system manufacturers, communication service providers (CSP), aircraft and equipment manufacturers, and ATS regulatory authorities to advise them of the airborne requirements and procedures, and the related assumptions. 2.2 This AMC provides a method for evaluating compliance of a data link system to the requirements of ED-89A, and the means by which an aircraft operator can satisfy an authority that operational considerations have been addressed. 3 SCOPE 3.1 This AMC addresses D-ATIS over ACARS using the ARINC 623 protocol as elaborated in EUROCAE document ED-89A and promoted by the EUROCONTROL Convergence and Implementation Plan as an interim data link application pending maturity of the LINK 2000+ programme. 3.2 Other implementation of D-ATIS service may exist in the world. They are not necessarily identical to the service defined within this AMC and EUROCAE document ED-89A. For example, application message formats may differ. Similarly, the ATSP may send ATIS information to an ACARS communication service provider who then distributes it to subscriber operators. This should not be considered as an air traffic service offered directly by an ATSP. In the USA, guidance on ATIS data link approval for use in the US airspace, may be found in FAA document 98-AIR D-ATIS: Safety and Interoperability Requirements for ATIS. 3.3 This AMC is not applicable to the phased implementation of data link services within the EUROCONTROL LINK2000+ programme, in particular, D-ATIS over the Aeronautical Telecommunications Network via VHF Digital Link (VDL) Mode 2. In this case, the Safety and Performance Requirements (EUROCAE ED-120) and the Interoperability Requirements (EUROCAE ED-110) have been established using EUROCAE document ED-78A, Guidelines for Approval of the Provision and use of Air Traffic Services supported by Data Communications. Guidance for the implementation of data link over ATN may be found in EASA document AMC 20-11. 3.4 The operational requirements for the D-ATIS application are published in EUROCONTROL document OPR/ET1/ST05/1000, Transition guidelines for initial air ground data communication services. 3.5 For the remainder of this document, the acronym D-ATIS should be interpreted to mean D-ATIS over ACARS using the ARINC 623 protocol in accordance with ED-89A unless stated otherwise. 4 REFERENCE DOCUMENTS 4.1 Related Requirements CS/FAR 25.1301, 25.1307, 25.1309, 25.1322, 25.1431, 25.1581, or equivalent requirements of CS 23, 27 and 29, if applicable. 4.2 Related Standards and Guidance Material <table border="1" cellpadding="0" cellspacing="0" width="529"><tr><td rowspan="4" valign="top" width="100"><p><b>ICAO</b></p></td><td valign="top" width="126"><p>Doc 9694 AN/955</p></td><td valign="top" width="303"><p>Manual of Air Traffic Services (ATS) Data Link Applications</p></td></tr><tr><td valign="top" width="126"><p>Doc 4444</p></td><td valign="top" width="303"><p>Rules of the Air and Air Traffic Services</p></td></tr><tr><td valign="top" width="126"><p>Annex 11</p></td><td valign="top" width="303"><p>Air Traffic Services</p></td></tr><tr><td valign="top" width="126"><p>Doc 8585</p></td><td valign="top" width="303"><p>Designators for Aircraft Operating agencies, Aeronautical Authorities and Services.</p></td></tr><tr><td valign="top" width="100"><p><b>EASA</b></p></td><td valign="top" width="126"><p>AMC 25-11</p></td><td valign="top" width="303"><p>Electronic Display Systems</p></td></tr><tr><td rowspan="3" valign="top" width="100"><p><b>EUROCONTROL</b></p></td><td valign="top" width="126"><p>CIP: COM.</p><p>ET2.SO4; 2.1.5</p></td><td valign="top" width="303"><p>Implement Air/Ground Communication Services- Interim step on non-ATN (ACARS) services.</p></td></tr><tr><td valign="top" width="126"><p>OPR/ET1/ST05/1000</p></td><td valign="top" width="303"><p>Transition guidelines for initial air ground data communication services </p></td></tr><tr><td valign="top" width="126"><p>ESARR 4</p></td><td valign="top" width="303"><p>Risk assessment and mitigation in ATM</p></td></tr><tr><td rowspan="4" valign="top" width="100"><p><b>FAA</b></p></td><td valign="top" width="126"><p>AC 25-11</p></td><td valign="top" width="303"><p>Electronic Display Systems. </p></td></tr><tr><td valign="top" width="126"><p>AC 120-70</p></td><td valign="top" width="303"><p>Initial Air Carrier Operational Approval for use of Digital Communication Systems</p></td></tr><tr><td valign="top" width="126"><p>AC 20-140</p></td><td valign="top" width="303"><p>Guidelines for design approval of aircraft data communications systems</p></td></tr><tr><td valign="top" width="126"><p>98-Air-D-ATIS </p></td><td valign="top" width="303"><p>Safety and Interoperability requirement for D-ATIS (Air-100, April 21,1998)</p></td></tr><tr><td rowspan="4" valign="top" width="100"><p><b>EUROCAE</b></p></td><td valign="top" width="126"><p>ED 78</p></td><td valign="top" width="303"><p>Guidance material for the establishment of data link supported ATS Services</p></td></tr><tr><td valign="top" width="126"><p>ED-89A</p></td><td valign="top" width="303"><p>Data Link Application System document (DLASD) for the “ATIS” data link service</p></td></tr><tr><td valign="top" width="126"><p>ED-92A</p></td><td valign="top" width="303"><p>Minimum Operational Performance specification for an airborne VDL Mode 2 Transceiver</p></td></tr><tr><td valign="top" width="126"><p>ED-112</p></td><td valign="top" width="303"><p>Minimum operational performance specification for Crash protected airborne recorder systems</p><p>Note: Includes criteria for recording of data link messages.</p></td></tr><tr><td valign="top" width="100"><p><b>RTCA</b></p></td><td valign="top" width="126"><p>DO-224</p></td><td valign="top" width="303"><p>Minimum Aviation System Performance Standards (MASPS) for Advanced VHF Digital Data Communications Including Compatibility with Digital Voice Techniques.</p></td></tr><tr><td valign="top" width="100"><p><b>SAE</b></p></td><td valign="top" width="126"><p>ARP 4791</p></td><td valign="top" width="303"><p>Human Machine Interface on the flight deck</p></td></tr></table> 5 ASSUMPTIONS Applicants should note that this AMC is based on the assumptions stated in Chapter 3 of document ED-89A together with the following that concern the measures taken by the responsible airspace authorities to safeguard operations affected by the transmission of D-ATIS. 5.1 ATS Provider 5.1.1 The data link service for ATIS has been shown to satisfy applicable airspace safety regulations and the relevant ATS domain performance, safety and interoperability requirements of ED-89A. 5.1.2 The ATS Provider ensures that information provided through D-ATIS service is fully consistent with the voice information broadcast over VHF. 5.1.3 Appropriate procedures are established to minimise the possibility of failure to detect any inconsistency in ATIS information for approach, landing and take off. 5.1.4 Each ATS provider has published a list of communication service providers that may be used by aircraft operators for the D-ATIS application. The list should take account of internetworking arrangements between service providers. 5.1.5 The procedures of the ATS provider state the actions that should be taken in the event of an inadequate communication service from the communications service provider. 5.2 Communications Service Provider The communications service provider does not modify the operational information (content and format) exchanged between the ATS provider and the airborne equipment. 5.3 Aeronautical Information Service The availability of the D-ATIS service, a statement of compliance with ED-89A, and additional relevant procedures are published in the AIP or other notification issued by the States where D-ATIS is offered. 5.4 Message Integrity The Cyclic Redundancy Check (CRC) is implemented as required by ED-89A and is providing integrity of the end-to-end data link transmission path. On this basis, Performance Technical Objective PTO\_3 of ED-89A need not be demonstrated by end systems. The PTO\_3 requirement is applicable only to the Communication Service Provider and limits the amount of corrupted messages that would be detected and rejected by end-systems. Note: The CRC is described in ARINC Specification 622 Chapter 5. 6 AIRWORTHINESS CONSIDERATIONS 6.1 General 6.1.1 The installation will need to meet the airborne domain requirements allocated as per ED-89A (§7.1) covering the Interoperability Operational Requirements, the Interoperability Technical Requirements, the Performance Technical Requirements, and the Safety Operational & Technical Requirements. 6.1.2 If multiple ATS data link applications are available to the aircraft, the crew interface and related crew procedures will need to be based on a common and compatible philosophy. 6.2 Required Functions An acceptable minimum airborne installation comprises the following functions: (a) A means of data communication appropriate to the area of operation, e.g. plain old ACARS over AVLC (Aviation VHF Link Control) through VHF or SATCOM; Note: VDL Mode 2 equipment can be used provided that radio transceiver is compliant with ED-92A. (b) A means to manage data communications and to control the data communications system. (c) A means to easily check and modify the D-ATIS request parameters. (d) A means of attracting the attention of the flight crew to an incoming message. Notes: (1) Activation of a printer may suffice to meet this need. (2) The means used will need to be such as to avoid confusion with other, non-data link, flight deck alerting devices. (3) The need for temporary suppression of the attention-getter during critical flight phases should be considered. (e) Means to display the text message, e.g. a single display readable by both pilots or a dedicated display for each pilot. For the interim deployment of D-ATIS over ACARS, a printer may serve as the primary display for messages subject to compliance with paragraph 7.3 of this AMC. 6.3 Recommended Functions (a) A means to print the message. (b) Recording of D-ATIS messages and flight crew requests on an accident flight recorder. Note: Data Link recording may be required in accordance with OPS rules. 7 ACCEPTABLE MEANS OF AIRWORTHINESS COMPLIANCE 7.1 Airworthiness 7.1.1 When demonstrating compliance with this AMC, the following should be noted: (a) Compliance with the airworthiness requirements for intended function and safety may be demonstrated by equipment qualification, safety analyses of the interfaces between components of the airborne communications equipment, structural analyses of new antenna installations, equipment cooling verification, and evidence of a suitable human to machine interface. The D-ATIS function will need to be demonstrated by end-to-end ground testing that verifies system operation, either with an appropriate ATS unit, or by means of test equipment that has been shown to be representative of an actual ATS unit. Note: This limited testing assumes that the communication systems (VHF or SATCOM) have been shown to satisfactorily perform their intended functions in the flight environment in accordance with applicable requirements. (b) The safety analysis of the interface between the ACARS and other systems should show that, under normal or fault conditions, no unwanted interaction that adversely affects essential systems can occur. (c) Where a printer is used as the primary display of the ATIS message, its readability should be shown to be adequate for this purpose, and that it does not present an unacceptable risk of an erroneous display. Note: This does not preclude the use of a printer classified as non-essential provided it has demonstrated a satisfactory in-service record that supports compliance with paragraph 7.3 of this AMC. 7.1.2 To minimise the certification effort for follow-on installations, the applicant may claim credit, from the responsible authority, for applicable certification and test data obtained from equivalent aircraft installations. 7.2 Performance The installation will need to be shown compliant with the airborne domain performance requirements allocated by ED-89A (§7.1). Demonstration of Performance Technical Requirement PTR\_A1 may be difficult for some airborne installations. The applicant may choose an alternative acceptable means of compliance for PTR\_A1 consisting in an end-to-end demonstration of PTR\_5 & PTR\_6 of ED-89A (§5.2) with an appropriate ATS unit and communication service provider. 7.3 Safety Objectives 7.3.1 Failure Conditions are presented in ED-89A (§6) together with the resulting safety objectives and operational means of mitigation. Failure Condition FC3 (Non-detected corrupted ATIS presented to an aircrew) requires that the occurrence of such a hazard at the aircraft level be demonstrated improbable. 7.3.2 ED-89A takes into account the possibility of using ACARS approved to earlier standards and classified as “non-essential” without guarantees of performance or integrity. Consequently, additional procedures are necessary to compensate for any deficiency and to safeguard operations. (See §8 of this AMC) 7.4 Aircraft Flight Manual The Aircraft Flight Manual (AFM) or the Pilot’s Operating Handbook (POH), whichever is applicable, should identify the D-ATIS over ACARS application as having been demonstrated with data link services declared compliant with EUROCAE document ED-89A. If certification was not achieved at the level “essential”, the AFM or POH, whichever is applicable,shall remind the crew that they are responsible for checking the D-ATIS information received over ACARS is consistent with their request, or revert to a voice ATIS. 7.5 Existing installations The applicant will need to submit a compliance statement that shows how the criteria of this AMC have been satisfied for existing installations. Compliance may be established by inspection of the installed system to confirm the availability of required features and functionality. Note: It is not intended that aircraft which have received airworthiness approval in compliance with ED 89 requirement should be reinvestigated where the installation is compliant with Section 6, 7 and 8 of this AMC. 8 OPERATIONAL CONSIDERATIONS 8.1 Operational Safety Aspects 8.1.1 Failure Conditions are presented in ED-89A (§6) together with the resulting safety requirements and operational means of mitigation. Failure Condition FC3 (Non-detected corrupted ATIS presented to an aircrew) is discussed further in the following paragraphs. 8.1.2 Applying existing ICAO operational procedures can independently verify the majority of ATIS parameters. Certain information may need to be verified by additional operational procedures. Examples include runway surface conditions, air and dew point temperatures, and other essential operational information. 8.1.3 If the aircraft system is classified and certified as “non-essential”, additional flight crew verification procedures will need to be defined to compensate for this deficiency. 8.1.4 When the airborne system is certified as “essential”, then integrity and performance can be considered as acceptable without a voice ATIS cross check unless otherwise required by the AIP. 8.1.5 It is important that crew are aware that they remain responsible for checking that received ATIS information corresponds to their request in terms of airfield name, date, type of ATIS (D or A) and type of contract. In case of inconsistency, reversion to voice ATIS is required. Note: ED-89A (§6) SOR-A1 (check of name of airfield), SOR-A2 (ATIS letter acknowledgement at first contact) and SOR-A3 (check of global consistency of information) require checks irrespective of the level of classification of the data link system 8.1.6 Flight crews will need to comply with any additional mitigating procedures published by the States where aircraft will operate and use a D-ATIS service. 8.1.7 The assumptions of Section 5 of this AMC need to be satisfied as a condition for operational use. 8.2 Operations Manual and Training 8.2.1 The Operations Manual shall reflect the Flight Manual statement of paragraph 7.4, and to define operating procedures for the use of D-ATIS via ACARS taking into account the Operational Considerations discussed in paragraph 8 of this AMC. 8.2.2 Similarly, flight crew training shall address: (a) The different data link services available using the same airborne equipment (e.g. differences between ATIS provided through D-ATIS service that are declared to conform to ED-89A requirements, and ATIS received through other means such as ACARS AOC). (b) The procedures for safe use of D-ATIS over ACARS. 8.2.3 Subject to any arrangements that may be required by the responsible operations authority in respect of amendments to the Operations Manual, and the approval of training programmes, the aircraft operator may implement operations using D-ATIS over ACARS without the need for further formal operational approval. 8.3 Incident reporting Significant incidents associated with a D-ATIS transmitted by data link that affects or could affect the safe operation of the aircraft will need to be reported in accordance with applicable operational rules. The incident should be reported also to the ATS authority responsible for the airport where the D-ATIS service is provided. AVAILABILITY OF DOCUMENTS EUROCAE documents may be purchased from EUROCAE, 17 rue Hamelin, 75783 Paris Cedex 16, France, (Fax: 33 1 45 05 72 30). Web site: [www.eurocae.org](http://www.eurocae.org) JAA documents are available from the JAA publisher Information Handling Services (IHS). Information on prices, where and how to order is available on both the JAA web site: www.jaa.nl and the IHS web site: [www.avdataworks.com](http://www.avdataworks.com). JAA documents transposed to publications of the European Aviation Safety Agency (EASA) are available on the EASA web site [www.easa.eu.int](http://www.easa.eu.int) EUROCONTROL documents may be requested from EUROCONTROL, Documentation Centre, GS4, Rue de la Fusee, 96, B-1130 Brussels, Belgium; (Fax: 32 2 729 9109). Web site: [www.eurocontrol.int](http://www.eurocontrol.int) ICAO documents may be purchased from Document Sales Unit, International Civil Aviation Organisation, 999 University Street, Montreal, Quebec, Canada H3C 5H7, (Fax: 1 514 954 6769, e-mail: sales\_unit@icao.org) or through national agencies. FAA documents may be obtained from Department of Transportation, Subsequent Distribution Office SVC-121.23, Ardmore East Business Centre, 3341 Q 75th Avenue, Landover, MD 20785, USA. RTCA documents may be obtained from RTCA Inc, 1828 L Street, NW. Suite 805, Washington, DC 20036, USA., (Tel: 1 202 833 9339; Fax 1 202 833 9434). Web site: [www.rtca.org](http://www.rtca.org) SAE documents may be obtained from SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA15096-0001, USA. Telephone 1-877-606-7323 (U.S. and Canada only) or 724/776-4970 (elsewhere). Web site: [www.sae.org](http://www.sae.org) [Amdt 20/1] --- [[7]](#_ftnref7) Information on LINK2000+ is available at web site [www.eurocontrol.int/link2000](http://www.eurocontrol.int/link2000) AMC 20-10Acceptable Means of Compliance for the Approval of Digital ATIS via Data Link over ACARS ED Decision 2006/012/R 1          PREAMBLE 1.1       This AMC is issued in response to the EUROCONTROL Convergence and Implementation Plan that recommends an interim deployment of air-to-ground and ground-to-air data link applications based on the existing airline ACARS technology. One such application is Digital Automated Terminal Information Services (D-ATIS) now planned to be operational at various airports in Europe. Aircraft operators, on a voluntary basis, may take advantage of D-ATIS where it is available, provided the service is verified in accordance with operational procedures acceptable to the responsible operations authority. 1.2       The use of ACARS for data link purposes is a transitional step to data link applications that will use VHF Digital Link (VDL) Mode 2 and the Aeronautical Telecommunications Network (ATN), compliant with ICAO SARPS, as proposed in the EUROCONTROL LINK2000+ programme[[7]](#_ftn7). 1.3       Described in EUROCAE document ED-89A, Data Link Application System document (DLASD) for the “ATIS” Data Link Service, D-ATIS is a control tower application providing direct communication of ATIS information to the flight crew and, optionally automatic updating of this information.  The ED-89A document addresses three domains: airborne, ground ATC, and communication service providers. It deals also with associated flight crew and air traffic service provider procedures. ED-89A incorporates the protocols and message formats formerly published in ARINC Specification 623, and takes account of EUROCAE document ED-78 which describes the global processes including approval planning, co-ordinated requirements determination, development and qualification of a system element, entry into service, and operations. 2.         PURPOSE 2.1       This AMC is intended for operators intending to use Digital ATIS over ACARS as described in document EUROCAE ED-89A. It may assist also other stakeholders such as airspace planners, air traffic service providers (ATSP), ATS system manufacturers, communication service providers (CSP), aircraft and equipment manufacturers, and ATS regulatory authorities to advise them of the airborne requirements and procedures, and the related assumptions. 2.2       This AMC provides a method for evaluating compliance of a data link system to the requirements of ED-89A, and the means by which an aircraft operator can satisfy an authority that operational considerations have been addressed. 3          SCOPE 3.1       This AMC addresses D-ATIS over ACARS using the ARINC 623 protocol as elaborated in EUROCAE document ED-89A and promoted by the EUROCONTROL Convergence and Implementation Plan as an interim data link application pending maturity of the LINK 2000+ programme. 3.2       Other implementation of D-ATIS service may exist in the world. They are not necessarily identical to the service defined within this AMC and EUROCAE document ED-89A. For example, application message formats may differ. Similarly, the ATSP may send ATIS information to an ACARS communication service provider who then distributes it to subscriber operators. This should not be considered as an air traffic service offered directly by an ATSP. In the USA, guidance on ATIS data link approval for use in the US airspace, may be found in FAA document 98-AIR D-ATIS: Safety and Interoperability Requirements for ATIS. 3.3       This AMC is not applicable to the phased implementation of data link services within the EUROCONTROL LINK2000+ programme, in particular, D-ATIS over the Aeronautical Telecommunications Network via VHF Digital Link (VDL) Mode 2. In this case, the Safety and Performance Requirements (EUROCAE ED-120) and the Interoperability Requirements (EUROCAE ED-110) have been established using EUROCAE document ED-78A, Guidelines for Approval of the Provision and use of Air Traffic Services supported by Data Communications. Guidance for the implementation of data link over ATN may be found in EASA document AMC 20-11. 3.4       The operational requirements for the D-ATIS application are published in EUROCONTROL document OPR/ET1/ST05/1000, Transition guidelines for initial air ground data communication services. 3.5       For the remainder of this document, the acronym D-ATIS should be interpreted to mean D-ATIS over ACARS using the ARINC 623 protocol in accordance with ED-89A unless stated otherwise. 4          REFERENCE DOCUMENTS 4.1       Related Requirements CS/FAR 25.1301, 25.1307, 25.1309, 25.1322, 25.1431, 25.1581, or equivalent requirements of CS 23, 27 and 29, if applicable. 4.2       Related Standards and Guidance Material <table border="1" cellpadding="0" cellspacing="0" width="529"> <tr> <td rowspan="4" valign="top" width="100"> <p><b>ICAO</b></p> </td> <td valign="top" width="126"> <p>Doc 9694 AN/955</p> </td> <td valign="top" width="303"> <p>Manual of Air Traffic Services (ATS) Data Link Applications</p> </td> </tr> <tr> <td valign="top" width="126"> <p>Doc 4444</p> </td> <td valign="top" width="303"> <p>Rules of the Air and Air Traffic Services</p> </td> </tr> <tr> <td valign="top" width="126"> <p>Annex 11</p> </td> <td valign="top" width="303"> <p>Air Traffic Services</p> </td> </tr> <tr> <td valign="top" width="126"> <p>Doc 8585</p> </td> <td valign="top" width="303"> <p>Designators for Aircraft Operating agencies, Aeronautical Authorities and Services.</p> </td> </tr> <tr> <td valign="top" width="100"> <p><b>EASA</b></p> </td> <td valign="top" width="126"> <p>AMC 25-11</p> </td> <td valign="top" width="303"> <p>Electronic Display Systems</p> </td> </tr> <tr> <td rowspan="3" valign="top" width="100"> <p><b>EUROCONTROL</b></p> </td> <td valign="top" width="126"> <p>CIP: COM.</p> <p>ET2.SO4; 2.1.5</p> </td> <td valign="top" width="303"> <p>Implement Air/Ground Communication Services- Interim step on non-ATN (ACARS) services.</p> </td> </tr> <tr> <td valign="top" width="126"> <p>OPR/ET1/ST05/1000</p> </td> <td valign="top" width="303"> <p>Transition guidelines for initial air ground data communication services </p> </td> </tr> <tr> <td valign="top" width="126"> <p>ESARR 4</p> </td> <td valign="top" width="303"> <p>Risk assessment and mitigation in ATM</p> </td> </tr> <tr> <td rowspan="4" valign="top" width="100"> <p><b>FAA</b></p> </td> <td valign="top" width="126"> <p>AC 25-11</p> </td> <td valign="top" width="303"> <p>Electronic Display Systems.  </p> </td> </tr> <tr> <td valign="top" width="126"> <p>AC 120-70</p> </td> <td valign="top" width="303"> <p>Initial Air Carrier Operational Approval for use of Digital Communication Systems</p> </td> </tr> <tr> <td valign="top" width="126"> <p>AC 20-140</p> </td> <td valign="top" width="303"> <p>Guidelines for design approval of aircraft data communications systems</p> </td> </tr> <tr> <td valign="top" width="126"> <p>98-Air-D-ATIS </p> </td> <td valign="top" width="303"> <p>Safety and Interoperability requirement for D-ATIS  (Air-100, April 21,1998)</p> </td> </tr> <tr> <td rowspan="4" valign="top" width="100"> <p><b>EUROCAE</b></p> </td> <td valign="top" width="126"> <p>ED 78</p> </td> <td valign="top" width="303"> <p>Guidance material for the establishment of data link supported ATS Services</p> </td> </tr> <tr> <td valign="top" width="126"> <p>ED-89A</p> </td> <td valign="top" width="303"> <p>Data Link Application System document (DLASD) for the “ATIS” data link service</p> </td> </tr> <tr> <td valign="top" width="126"> <p>ED-92A</p> </td> <td valign="top" width="303"> <p>Minimum Operational Performance specification for an airborne VDL Mode 2 Transceiver</p> </td> </tr> <tr> <td valign="top" width="126"> <p>ED-112</p> </td> <td valign="top" width="303"> <p>Minimum operational performance specification for Crash protected airborne recorder systems</p> <p>Note: Includes criteria for recording of data link messages.</p> </td> </tr> <tr> <td valign="top" width="100"> <p><b>RTCA</b></p> </td> <td valign="top" width="126"> <p>DO-224</p> </td> <td valign="top" width="303"> <p>Minimum Aviation System Performance Standards (MASPS) for Advanced VHF Digital Data Communications Including Compatibility with Digital Voice Techniques.</p> </td> </tr> <tr> <td valign="top" width="100"> <p><b>SAE</b></p> </td> <td valign="top" width="126"> <p>ARP 4791</p> </td> <td valign="top" width="303"> <p>Human Machine Interface on the flight deck</p> </td> </tr> </table> 5          ASSUMPTIONS Applicants should note that this AMC is based on the assumptions stated in Chapter 3 of document ED-89A together with the following that concern the measures taken by the responsible airspace authorities to safeguard operations affected by the transmission of D-ATIS. 5.1       ATS Provider 5.1.1   The data link service for ATIS has been shown to satisfy applicable airspace safety regulations and the relevant ATS domain performance, safety and interoperability requirements of ED-89A. 5.1.2   The ATS Provider ensures that information provided through D-ATIS service is fully consistent with the voice information broadcast over VHF. 5.1.3   Appropriate procedures are established to minimise the possibility of failure to detect any inconsistency in ATIS information for approach, landing and take off. 5.1.4   Each ATS provider has published a list of communication service providers that may be used by aircraft operators for the D-ATIS application. The list should take account of internetworking arrangements between service providers. 5.1.5 The procedures of the ATS provider state the actions that should be taken in the event of an inadequate communication service from the communications service provider. 5.2       Communications Service Provider The communications service provider does not modify the operational information (content and format) exchanged between the ATS provider and the airborne equipment. 5.3       Aeronautical Information Service The availability of the D-ATIS service, a statement of compliance with ED-89A, and additional relevant procedures are published in the AIP or other notification issued by the States where D-ATIS is offered. 5.4       Message Integrity The Cyclic Redundancy Check (CRC) is implemented as required by ED-89A and is providing integrity of the end-to-end data link transmission path. On this basis, Performance Technical Objective PTO\_3 of ED-89A need not be demonstrated by end systems. The PTO\_3 requirement is applicable only to the Communication Service Provider and limits the amount of corrupted messages that would be detected and rejected by end-systems. Note: The CRC is described in ARINC Specification 622 Chapter 5. 6          AIRWORTHINESS CONSIDERATIONS 6.1       General 6.1.1   The installation will need to meet the airborne domain requirements allocated as per ED-89A (§7.1) covering the Interoperability Operational Requirements, the Interoperability Technical Requirements, the Performance Technical Requirements, and the Safety Operational & Technical Requirements. 6.1.2   If multiple ATS data link applications are available to the aircraft, the crew interface and related crew procedures will need to be based on a common and compatible philosophy. 6.2       Required Functions An acceptable minimum airborne installation comprises the following functions: (a)       A means of data communication appropriate to the area of operation, e.g. plain old ACARS over AVLC (Aviation VHF Link Control) through VHF or SATCOM;              Note: VDL Mode 2 equipment can be used provided that radio transceiver is compliant with ED-92A. (b)      A means to manage data communications and to control the data communications system. (c)       A means to easily check and modify the D-ATIS request parameters. (d)      A means of attracting the attention of the flight crew to an incoming message. Notes: (1)       Activation of a printer may suffice to meet this need. (2)       The means used will need to be such as to avoid confusion with            other, non-data link, flight deck alerting devices. (3)       The need for temporary suppression of the attention-getter during     critical flight phases should be considered. (e)      Means to display the text message, e.g. a single display readable by both pilots or a dedicated display for each pilot.  For the interim deployment of D-ATIS over ACARS, a printer may serve as the primary display for messages subject to compliance with paragraph 7.3 of this AMC. 6.3       Recommended Functions (a)       A means to print the message. (b)      Recording of D-ATIS messages and flight crew requests on an accident flight recorder. Note: Data Link recording may be required in accordance with OPS rules. 7          ACCEPTABLE MEANS OF AIRWORTHINESS COMPLIANCE 7.1       Airworthiness 7.1.1   When demonstrating compliance with this AMC, the following should be noted: (a)       Compliance with the airworthiness requirements for intended function and safety may be demonstrated by equipment qualification, safety analyses of the interfaces between components of the airborne communications equipment, structural analyses of new antenna installations, equipment cooling verification, and evidence of a suitable human to machine interface. The D-ATIS function will need to be demonstrated by end-to-end ground testing that verifies system operation, either with an appropriate ATS unit, or by means of test equipment that has been shown to be representative of an actual ATS unit. Note: This limited testing assumes that the communication systems (VHF or SATCOM) have been shown to satisfactorily perform their intended functions in the flight environment in accordance with applicable requirements. (b)       The safety analysis of the interface between the ACARS and other systems should show that, under normal or fault conditions, no unwanted interaction that adversely affects essential systems can occur. (c)       Where a printer is used as the primary display of the ATIS message, its readability should be shown to be adequate for this purpose, and that it does not present an unacceptable risk of an erroneous display. Note: This does not preclude the use of a printer classified as non-essential provided it has demonstrated a satisfactory in-service record that supports compliance with paragraph 7.3 of this AMC. 7.1.2   To minimise the certification effort for follow-on installations, the applicant may claim credit, from the responsible authority, for applicable certification and test data obtained from equivalent aircraft installations. 7.2       Performance The installation will need to be shown compliant with the airborne domain performance requirements allocated by ED-89A (§7.1). Demonstration of Performance Technical Requirement PTR\_A1 may be difficult for some airborne installations. The applicant may choose an alternative acceptable means of compliance for PTR\_A1 consisting in an end-to-end demonstration of PTR\_5 & PTR\_6 of ED-89A (§5.2) with an appropriate ATS unit and communication service provider. 7.3       Safety Objectives 7.3.1   Failure Conditions are presented in ED-89A (§6) together with the resulting safety objectives and operational means of mitigation. Failure Condition FC3 (Non-detected corrupted ATIS presented to an aircrew) requires that the occurrence of such a hazard at the aircraft level be demonstrated improbable. 7.3.2   ED-89A takes into account the possibility of using ACARS approved to earlier standards and classified as “non-essential” without guarantees of performance or integrity. Consequently, additional procedures are necessary to compensate for any deficiency and to safeguard operations. (See §8 of this AMC) 7.4       Aircraft Flight Manual The Aircraft Flight Manual (AFM) or the Pilot’s Operating Handbook (POH), whichever is applicable, should identify the D-ATIS over ACARS application as having been demonstrated with data link services declared compliant with EUROCAE document ED-89A. If certification was not achieved at the level “essential”, the AFM or POH, whichever is applicable,shall remind the crew that they are responsible for checking the D-ATIS information received over ACARS is consistent with their request, or revert to a voice ATIS. 7.5       Existing installations The applicant will need to submit a compliance statement that shows how the criteria of this AMC have been satisfied for existing installations. Compliance may be established by inspection of the installed system to confirm the availability of required features and functionality. Note: It is not intended that aircraft which have received airworthiness approval in compliance with ED 89 requirement should be reinvestigated where the installation is compliant with Section 6, 7 and 8 of this AMC. 8          OPERATIONAL CONSIDERATIONS 8.1       Operational Safety Aspects 8.1.1   Failure Conditions are presented in ED-89A (§6) together with the resulting safety requirements and operational means of mitigation. Failure Condition FC3 (Non-detected corrupted ATIS presented to an aircrew) is discussed further in the following paragraphs. 8.1.2   Applying existing ICAO operational procedures can independently verify the majority of ATIS parameters. Certain information may need to be verified by additional operational procedures. Examples include runway surface conditions, air and dew point temperatures, and other essential operational information. 8.1.3   If the aircraft system is classified and certified as “non-essential”, additional flight crew verification procedures will need to be defined to compensate for this deficiency. 8.1.4   When the airborne system is certified as “essential”, then integrity and performance can be considered as acceptable without a voice ATIS cross check unless otherwise required by the AIP. 8.1.5   It is important that crew are aware that they remain responsible for checking that received ATIS information corresponds to their request in terms of airfield name, date, type of ATIS (D or A) and type of contract. In case of inconsistency, reversion to voice ATIS is required. Note: ED-89A (§6) SOR-A1 (check of name of airfield), SOR-A2 (ATIS letter acknowledgement at first contact) and SOR-A3 (check of global consistency of information) require checks irrespective of the level of classification of the data link system 8.1.6   Flight crews will need to comply with any additional mitigating procedures published by the States where aircraft will operate and use a D-ATIS service. 8.1.7   The assumptions of Section 5 of this AMC need to be satisfied as a condition for operational use. 8.2       Operations Manual and Training 8.2.1   The Operations Manual shall reflect the Flight Manual statement of paragraph 7.4, and to define operating procedures for the use of D-ATIS via ACARS taking into account the Operational Considerations discussed in paragraph 8 of this AMC. 8.2.2   Similarly, flight crew training shall address: (a)       The different data link services available using the same airborne equipment (e.g. differences between ATIS provided through D-ATIS service that are declared to conform to ED-89A requirements, and ATIS received through other means such as ACARS AOC). (b)       The procedures for safe use of D-ATIS over ACARS. 8.2.3   Subject to any arrangements that may be required by the responsible operations authority in respect of amendments to the Operations Manual, and the approval of training programmes, the aircraft operator may implement operations using D-ATIS over ACARS without the need for further formal operational approval. 8.3       Incident reporting Significant incidents associated with a D-ATIS transmitted by data link that affects or could affect the safe operation of the aircraft will need to be reported in accordance with applicable operational rules. The incident should be reported also to the ATS authority responsible for the airport where the D-ATIS service is provided. AVAILABILITY OF DOCUMENTS EUROCAE documents may be purchased from EUROCAE, 17 rue Hamelin, 75783 Paris Cedex 16, France, (Fax: 33 1 45 05 72 30). Web site: [www.eurocae.org](http://www.eurocae.org) JAA documents are available from the JAA publisher Information Handling Services (IHS). Information on prices, where and how to order is available on both the JAA web site: www.jaa.nl and the IHS web site: [www.avdataworks.com](http://www.avdataworks.com). JAA documents transposed to publications of the European Aviation Safety Agency (EASA) are available on the EASA web site [www.easa.eu.int](http://www.easa.eu.int) EUROCONTROL documents may be requested from EUROCONTROL, Documentation Centre, GS4, Rue de la Fusee, 96, B-1130 Brussels, Belgium; (Fax: 32 2 729 9109). Web site: [www.eurocontrol.int](http://www.eurocontrol.int) ICAO documents may be purchased from Document Sales Unit, International Civil Aviation Organisation, 999 University Street, Montreal, Quebec, Canada H3C 5H7, (Fax: 1 514 954 6769, e-mail: sales\_unit@icao.org) or through national agencies. FAA documents may be obtained from Department of Transportation, Subsequent Distribution Office SVC-121.23, Ardmore East Business Centre, 3341 Q 75th Avenue, Landover, MD 20785, USA. RTCA documents may be obtained from RTCA Inc, 1828 L Street, NW. Suite 805, Washington, DC 20036, USA., (Tel: 1 202 833 9339; Fax 1 202 833 9434). Web site: [www.rtca.org](http://www.rtca.org) SAE documents may be obtained from SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA15096-0001, USA. Telephone 1-877-606-7323 (U.S. and Canada only) or 724/776-4970 (elsewhere). Web site: [www.sae.org](http://www.sae.org) [Amdt 20/1] --- [[7]](#_ftnref7)     Information on LINK2000+ is available at web site [www.eurocontrol.int/link2000](http://www.eurocontrol.int/link2000) AMC 20-10Acceptable Means of Compliance for the Approval of Digital ATIS via Data Link over ACARS ED Decision 2006/012/R 1          PREAMBLE 1.1       This AMC is issued in response to the EUROCONTROL Convergence and Implementation Plan that recommends an interim deployment of air-to-ground and ground-to-air data link applications based on the existing airline ACARS technology. One such application is Digital Automated Terminal Information Services (D-ATIS) now planned to be operational at various airports in Europe. Aircraft operators, on a voluntary basis, may take advantage of D-ATIS where it is available, provided the service is verified in accordance with operational procedures acceptable to the responsible operations authority. 1.2       The use of ACARS for data link purposes is a transitional step to data link applications that will use VHF Digital Link (VDL) Mode 2 and the Aeronautical Telecommunications Network (ATN), compliant with ICAO SARPS, as proposed in the EUROCONTROL LINK2000+ programme[[7]](#_ftn7). 1.3       Described in EUROCAE document ED-89A, Data Link Application System document (DLASD) for the “ATIS” Data Link Service, D-ATIS is a control tower application providing direct communication of ATIS information to the flight crew and, optionally automatic updating of this information. The ED-89A document addresses three domains: airborne, ground ATC, and communication service providers. It deals also with associated flight crew and air traffic service provider procedures. ED-89A incorporates the protocols and message formats formerly published in ARINC Specification 623, and takes account of EUROCAE document ED-78 which describes the global processes including approval planning, co-ordinated requirements determination, development and qualification of a system element, entry into service, and operations. 2.         PURPOSE 2.1       This AMC is intended for operators intending to use Digital ATIS over ACARS as described in document EUROCAE ED-89A. It may assist also other stakeholders such as airspace planners, air traffic service providers (ATSP), ATS system manufacturers, communication service providers (CSP), aircraft and equipment manufacturers, and ATS regulatory authorities to advise them of the airborne requirements and procedures, and the related assumptions. 2.2       This AMC provides a method for evaluating compliance of a data link system to the requirements of ED-89A, and the means by which an aircraft operator can satisfy an authority that operational considerations have been addressed. 3          SCOPE 3.1       This AMC addresses D-ATIS over ACARS using the ARINC 623 protocol as elaborated in EUROCAE document ED-89A and promoted by the EUROCONTROL Convergence and Implementation Plan as an interim data link application pending maturity of the LINK 2000+ programme. 3.2       Other implementation of D-ATIS service may exist in the world. They are not necessarily identical to the service defined within this AMC and EUROCAE document ED-89A. For example, application message formats may differ. Similarly, the ATSP may send ATIS information to an ACARS communication service provider who then distributes it to subscriber operators. This should not be considered as an air traffic service offered directly by an ATSP. In the USA, guidance on ATIS data link approval for use in the US airspace, may be found in FAA document 98-AIR D-ATIS: Safety and Interoperability Requirements for ATIS. 3.3       This AMC is not applicable to the phased implementation of data link services within the EUROCONTROL LINK2000+ programme, in particular, D-ATIS over the Aeronautical Telecommunications Network via VHF Digital Link (VDL) Mode 2. In this case, the Safety and Performance Requirements (EUROCAE ED-120) and the Interoperability Requirements (EUROCAE ED-110) have been established using EUROCAE document ED-78A, Guidelines for Approval of the Provision and use of Air Traffic Services supported by Data Communications. Guidance for the implementation of data link over ATN may be found in EASA document AMC 20-11. 3.4       The operational requirements for the D-ATIS application are published in EUROCONTROL document OPR/ET1/ST05/1000, Transition guidelines for initial air ground data communication services. 3.5       For the remainder of this document, the acronym D-ATIS should be interpreted to mean D-ATIS over ACARS using the ARINC 623 protocol in accordance with ED-89A unless stated otherwise. 4          REFERENCE DOCUMENTS 4.1       Related Requirements CS/FAR 25.1301, 25.1307, 25.1309, 25.1322, 25.1431, 25.1581, or equivalent requirements of CS 23, 27 and 29, if applicable. 4.2       Related Standards and Guidance Material <table border="1" cellpadding="0" cellspacing="0" width="529"> <tr> <td rowspan="4" valign="top" width="100"> <p><b>ICAO</b></p> </td> <td valign="top" width="126"> <p>Doc 9694 AN/955</p> </td> <td valign="top" width="303"> <p>Manual of Air Traffic Services (ATS) Data Link Applications</p> </td> </tr> <tr> <td valign="top" width="126"> <p>Doc 4444</p> </td> <td valign="top" width="303"> <p>Rules of the Air and Air Traffic Services</p> </td> </tr> <tr> <td valign="top" width="126"> <p>Annex 11</p> </td> <td valign="top" width="303"> <p>Air Traffic Services</p> </td> </tr> <tr> <td valign="top" width="126"> <p>Doc 8585</p> </td> <td valign="top" width="303"> <p>Designators for Aircraft Operating agencies, Aeronautical Authorities and Services.</p> </td> </tr> <tr> <td valign="top" width="100"> <p><b>EASA</b></p> </td> <td valign="top" width="126"> <p>AMC 25-11</p> </td> <td valign="top" width="303"> <p>Electronic Display Systems</p> </td> </tr> <tr> <td rowspan="3" valign="top" width="100"> <p><b>EUROCONTROL</b></p> </td> <td valign="top" width="126"> <p>CIP: COM.</p> <p>ET2.SO4; 2.1.5</p> </td> <td valign="top" width="303"> <p>Implement Air/Ground Communication Services- Interim step on non-ATN (ACARS) services.</p> </td> </tr> <tr> <td valign="top" width="126"> <p>OPR/ET1/ST05/1000</p> </td> <td valign="top" width="303"> <p>Transition guidelines for initial air ground data communication services </p> </td> </tr> <tr> <td valign="top" width="126"> <p>ESARR 4</p> </td> <td valign="top" width="303"> <p>Risk assessment and mitigation in ATM</p> </td> </tr> <tr> <td rowspan="4" valign="top" width="100"> <p><b>FAA</b></p> </td> <td valign="top" width="126"> <p>AC 25-11</p> </td> <td valign="top" width="303"> <p>Electronic Display Systems.  </p> </td> </tr> <tr> <td valign="top" width="126"> <p>AC 120-70</p> </td> <td valign="top" width="303"> <p>Initial Air Carrier Operational Approval for use of Digital Communication Systems</p> </td> </tr> <tr> <td valign="top" width="126"> <p>AC 20-140</p> </td> <td valign="top" width="303"> <p>Guidelines for design approval of aircraft data communications systems</p> </td> </tr> <tr> <td valign="top" width="126"> <p>98-Air-D-ATIS </p> </td> <td valign="top" width="303"> <p>Safety and Interoperability requirement for D-ATIS  (Air-100, April 21,1998)</p> </td> </tr> <tr> <td rowspan="4" valign="top" width="100"> <p><b>EUROCAE</b></p> </td> <td valign="top" width="126"> <p>ED 78</p> </td> <td valign="top" width="303"> <p>Guidance material for the establishment of data link supported ATS Services</p> </td> </tr> <tr> <td valign="top" width="126"> <p>ED-89A</p> </td> <td valign="top" width="303"> <p>Data Link Application System document (DLASD) for the “ATIS” data link service</p> </td> </tr> <tr> <td valign="top" width="126"> <p>ED-92A</p> </td> <td valign="top" width="303"> <p>Minimum Operational Performance specification for an airborne VDL Mode 2 Transceiver</p> </td> </tr> <tr> <td valign="top" width="126"> <p>ED-112</p> </td> <td valign="top" width="303"> <p>Minimum operational performance specification for Crash protected airborne recorder systems</p> <p>Note: Includes criteria for recording of data link messages.</p> </td> </tr> <tr> <td valign="top" width="100"> <p><b>RTCA</b></p> </td> <td valign="top" width="126"> <p>DO-224</p> </td> <td valign="top" width="303"> <p>Minimum Aviation System Performance Standards (MASPS) for Advanced VHF Digital Data Communications Including Compatibility with Digital Voice Techniques.</p> </td> </tr> <tr> <td valign="top" width="100"> <p><b>SAE</b></p> </td> <td valign="top" width="126"> <p>ARP 4791</p> </td> <td valign="top" width="303"> <p>Human Machine Interface on the flight deck</p> </td> </tr> </table> 5          ASSUMPTIONS Applicants should note that this AMC is based on the assumptions stated in Chapter 3 of document ED-89A together with the following that concern the measures taken by the responsible airspace authorities to safeguard operations affected by the transmission of D-ATIS. 5.1       ATS Provider 5.1.1   The data link service for ATIS has been shown to satisfy applicable airspace safety regulations and the relevant ATS domain performance, safety and interoperability requirements of ED-89A. 5.1.2   The ATS Provider ensures that information provided through D-ATIS service is fully consistent with the voice information broadcast over VHF. 5.1.3   Appropriate procedures are established to minimise the possibility of failure to detect any inconsistency in ATIS information for approach, landing and take off. 5.1.4   Each ATS provider has published a list of communication service providers that may be used by aircraft operators for the D-ATIS application. The list should take account of internetworking arrangements between service providers. 5.1.5 The procedures of the ATS provider state the actions that should be taken in the event of an inadequate communication service from the communications service provider. 5.2       Communications Service Provider The communications service provider does not modify the operational information (content and format) exchanged between the ATS provider and the airborne equipment. 5.3       Aeronautical Information Service The availability of the D-ATIS service, a statement of compliance with ED-89A, and additional relevant procedures are published in the AIP or other notification issued by the States where D-ATIS is offered. 5.4       Message Integrity The Cyclic Redundancy Check (CRC) is implemented as required by ED-89A and is providing integrity of the end-to-end data link transmission path. On this basis, Performance Technical Objective PTO\_3 of ED-89A need not be demonstrated by end systems. The PTO\_3 requirement is applicable only to the Communication Service Provider and limits the amount of corrupted messages that would be detected and rejected by end-systems. Note: The CRC is described in ARINC Specification 622 Chapter 5. 6          AIRWORTHINESS CONSIDERATIONS 6.1       General 6.1.1   The installation will need to meet the airborne domain requirements allocated as per ED-89A (§7.1) covering the Interoperability Operational Requirements, the Interoperability Technical Requirements, the Performance Technical Requirements, and the Safety Operational & Technical Requirements. 6.1.2   If multiple ATS data link applications are available to the aircraft, the crew interface and related crew procedures will need to be based on a common and compatible philosophy. 6.2       Required Functions An acceptable minimum airborne installation comprises the following functions: (a)       A means of data communication appropriate to the area of operation, e.g. plain old ACARS over AVLC (Aviation VHF Link Control) through VHF or SATCOM;              Note: VDL Mode 2 equipment can be used provided that radio transceiver is compliant with ED-92A. (b)      A means to manage data communications and to control the data communications system. (c)       A meansto easily check and modify the D-ATIS request parameters. (d)      A means of attracting the attention of the flight crew to an incoming message. Notes: (1)       Activation of a printer may suffice to meet this need. (2)       The means used will need to be such as to avoid confusion with            other, non-data link, flight deck alerting devices. (3)       The need for temporary suppression of the attention-getter during     critical flight phases should be considered. (e)      Means to display the text message, e.g. a single display readable by both pilots or a dedicated display for each pilot. For the interim deployment of D-ATIS over ACARS, a printer may serve as the primary display for messages subject to compliance with paragraph 7.3 of this AMC. 6.3       Recommended Functions (a)       A means to print the message. (b)      Recording of D-ATIS messages and flight crew requests on an accident flight recorder. Note: Data Link recording may be required in accordance with OPS rules. 7          ACCEPTABLE MEANS OF AIRWORTHINESS COMPLIANCE 7.1       Airworthiness 7.1.1   When demonstrating compliance with this AMC, the following should be noted: (a)       Compliance with the airworthiness requirements for intended function and safety may be demonstrated by equipment qualification, safety analyses of the interfaces between components of the airborne communications equipment, structural analyses of new antenna installations, equipment cooling verification, and evidence of a suitable human to machine interface. The D-ATIS function will need to be demonstrated by end-to-end ground testing that verifies system operation, either with an appropriate ATS unit, or by means of test equipment that has been shown to be representative of an actual ATS unit. Note: This limited testing assumes that the communication systems (VHF or SATCOM) have been shown to satisfactorily perform their intended functions in the flight environment in accordance with applicable requirements. (b)       The safety analysis of the interface between the ACARS and other systems should show that, under normal or fault conditions, no unwanted interaction that adversely affects essential systems can occur. (c)       Where a printer is used as the primary display of the ATIS message, its readability should be shown to be adequate for this purpose, and that it does not present an unacceptable risk of an erroneous display. Note: This does not preclude the use of a printer classified as non-essential provided it has demonstrated a satisfactory in-service record that supports compliance with paragraph 7.3 of this AMC. 7.1.2   To minimise the certification effort for follow-on installations, the applicant may claim credit, from the responsible authority, for applicable certification and test data obtained from equivalent aircraft installations. 7.2       Performance The installation will need to be shown compliant with the airborne domain performance requirements allocated by ED-89A (§7.1). Demonstration of Performance Technical Requirement PTR\_A1 may be difficult for some airborne installations. The applicant may choose an alternative acceptable means of compliance for PTR\_A1 consisting in an end-to-end demonstration of PTR\_5 & PTR\_6 of ED-89A (§5.2) with an appropriate ATS unit and communication service provider. 7.3       Safety Objectives 7.3.1   Failure Conditions are presented in ED-89A (§6) together with the resulting safety objectives and operational means of mitigation. Failure Condition FC3 (Non-detected corrupted ATIS presented to an aircrew) requires that the occurrence of such a hazard at the aircraft level be demonstrated improbable. 7.3.2   ED-89A takes into account the possibility of using ACARS approved to earlier standards and classified as “non-essential” without guarantees of performance or integrity. Consequently, additional procedures are necessary to compensate for any deficiency and to safeguard operations. (See §8 of this AMC) 7.4       Aircraft Flight Manual The Aircraft Flight Manual (AFM) or the Pilot’s Operating Handbook (POH), whichever is applicable, should identify the D-ATIS over ACARS application as having been demonstrated with data link services declared compliant with EUROCAE document ED-89A. If certification was not achieved at the level “essential”, the AFM or POH, whichever is applicable,shall remind the crew that they are responsible for checking the D-ATIS information received over ACARS is consistent with their request, or revert to a voice ATIS. 7.5       Existing installations The applicant will need to submit a compliance statement that shows how the criteria of this AMC have been satisfied for existing installations. Compliance may be established by inspection of the installed system to confirm the availability of required features and functionality. Note: It is not intended that aircraft which have received airworthiness approval in compliance with ED 89 requirement should be reinvestigated where the installation is compliant with Section 6, 7 and 8 of this AMC. 8          OPERATIONAL CONSIDERATIONS 8.1       Operational Safety Aspects 8.1.1   Failure Conditions are presented in ED-89A (§6) together with the resulting safety requirements and operational means of mitigation. Failure Condition FC3 (Non-detected corrupted ATIS presented to an aircrew) is discussed further in the following paragraphs. 8.1.2   Applying existing ICAO operational procedures can independently verify the majority of ATIS parameters. Certain information may need to be verified by additional operational procedures. Examples include runway surface conditions, air and dew point temperatures, and other essential operational information. 8.1.3   If the aircraft system is classified and certified as “non-essential”, additional flight crew verification procedures will need to be defined to compensate for this deficiency. 8.1.4   When the airborne system is certified as “essential”, then integrity and performance can be considered as acceptable without a voice ATIS cross check unless otherwise required by the AIP. 8.1.5   It is important that crew are aware that they remain responsible for checking that received ATIS information corresponds to their request in terms of airfield name, date, type of ATIS (D or A) and type of contract. In case of inconsistency, reversion to voice ATIS is required. Note: ED-89A (§6) SOR-A1 (check of name of airfield), SOR-A2 (ATIS letter acknowledgement at first contact) and SOR-A3 (check of global consistency of information) require checks irrespective of the level of classification of the data link system 8.1.6   Flight crews will need to comply with any additional mitigating procedures published by the States where aircraft will operate and use a D-ATIS service. 8.1.7   The assumptions of Section 5 of this AMC need to be satisfied as a condition for operational use. 8.2       Operations Manual and Training 8.2.1   The Operations Manual shall reflect the Flight Manual statement of paragraph 7.4, and to define operating procedures for the use of D-ATIS via ACARS taking into account the Operational Considerations discussed in paragraph 8 of this AMC. 8.2.2   Similarly, flight crew training shall address: (a)       The different data link services available using the same airborne equipment (e.g. differences between ATIS provided through D-ATIS service that are declared to conform to ED-89A requirements, and ATIS received through other means such as ACARS AOC). (b)       The procedures for safe use of D-ATIS over ACARS. 8.2.3   Subject to any arrangements that may be required by the responsible operations authority in respect of amendments to the Operations Manual, and the approval of training programmes, the aircraft operator may implement operations using D-ATIS over ACARS without the need for further formal operational approval. 8.3       Incident reporting Significant incidents associated with a D-ATIS transmitted by data link that affects or could affect the safe operation of the aircraft will need to be reported in accordance with applicable operational rules. The incident should be reported also to the ATS authority responsible for the airport where the D-ATIS service is provided. AVAILABILITY OF DOCUMENTS EUROCAE documents may be purchased from EUROCAE, 17 rue Hamelin, 75783 Paris Cedex 16, France, (Fax: 33 1 45 05 72 30). Web site: [www.eurocae.org](http://www.eurocae.org) JAA documents are available from the JAA publisher Information Handling Services (IHS). Information on prices, where and how to order is available on both the JAA web site: www.jaa.nl and the IHS web site: [www.avdataworks.com](http://www.avdataworks.com). JAA documents transposed to publications of the European Aviation Safety Agency (EASA) are available on the EASA web site [www.easa.eu.int](http://www.easa.eu.int) EUROCONTROL documents may be requested from EUROCONTROL, Documentation Centre, GS4, Rue de la Fusee, 96, B-1130 Brussels, Belgium; (Fax: 32 2 729 9109). Web site: [www.eurocontrol.int](http://www.eurocontrol.int) ICAO documents may be purchased from Document Sales Unit, International Civil Aviation Organisation, 999 University Street, Montreal, Quebec, Canada H3C 5H7, (Fax: 1 514 954 6769, e-mail: sales\_unit@icao.org) or through national agencies. FAA documents may be obtained from Department of Transportation, Subsequent Distribution Office SVC-121.23, Ardmore East Business Centre, 3341 Q 75th Avenue, Landover, MD 20785, USA. RTCA documents may be obtained from RTCA Inc, 1828 L Street, NW. Suite 805, Washington, DC 20036, USA., (Tel: 1 202 833 9339; Fax 1 202 833 9434). Web site: [www.rtca.org](http://www.rtca.org) SAE documents may be obtained from SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA15096-0001, USA. Telephone 1-877-606-7323 (U.S. and Canada only) or 724/776-4970 (elsewhere). Web site: [www.sae.org](http://www.sae.org) [Amdt 20/1] --- [[7]](#_ftnref7)     Information on LINK2000+ is available at web site [www.eurocontrol.int/link2000](http://www.eurocontrol.int/link2000)