21.A.307 The eligibility of parts and appliances for installation

• Regulation (EU) 2022/1358 found in: Initial Airworthiness and Environmental Protection (748/2012) Part-21 Part-21L (Jul 2024)

21.A.307 The eligibility of parts and appliances for installation Regulation (EU) 2022/1358 (a)     A part or appliance is eligible for installation in a type-certified product when it is in a condition for safe operation, marked in accordance with Subpart Q and accompanied by an authorised release certificate ([EASA Form 1](#_DxCrossRefBm1649096870)), certifying that the item was manufactured in conformity with approved design data. (b)     By way of derogation from point (a) and provided that the conditions in point (c) are met, the following parts or appliances do not require an [EASA Form 1](#_DxCrossRefBm1649096870) in order to be eligible for installation in a type-certified product: (1)     a standard part; (2)     in the case of ELA1 or ELA2, a part or appliance that is: (i)      not life limited, nor part of the primary structure, nor part of the flight controls; (ii)     identified for installation in the specific aircraft; (iii)     to be installed in an aircraft whose owner has verified compliance with the applicable conditions in (i) and (ii), and has accepted responsibility for this compliance; (3)     a part or appliance for which the consequences of a non-conformity with its approved design data has a negligible safety effect on the product and which is identified as such by the holder of the design approval in the instructions for continued airworthiness. In order to determine the safety effects of a non-conforming part or appliance, the design approval holder may establish in the instructions for continued airworthiness specific verification activities to be conducted by the installer of the part or appliance on the product; (4)     in the case of the embodiment of a standard change in accordance with point [21.A.90B](#_DxCrossRefBm1649097031) or a standard repair in accordance with point [21.A.431B](#_DxCrossRefBm1649097402), a part or appliance, for which the consequences of a non-conformity with its design data have a negligible safety effect on the product, and which is identified as such in the certification specifications for standard changes and standard repairs issued in accordance with point (a)(2) of point [21.A.90B](#_DxCrossRefBm1649097031) and point (a)(2) of point [21.A.431B](#_DxCrossRefBm1649097402). In order to determine the safety effects of a non-conforming part or appliance, specific verification activities to be conducted by the person that installs the part or appliance on the product may be established in the certification specifications referred to above; (5)     a part or appliance that is exempted from an airworthiness approval in accordance with [Commission Regulation (EU) No 965/2012](https://eur-lex.europa.eu/legal-content/EN/TXT/?uri=CELEX%3A32012R0965&qid=1649401475582) ([[34]](#_ftn34)); and (6)     a part or appliance that is an item of a higher assembly identified in points (b)(1) to (b)(5). (7)     a part or appliance manufactured by a person or organisation referred to in [Article 9](#_DxCrossRefBm1649096869)(4) of this Regulation; (c)      Parts and appliances listed in point (b) are eligible for installation in a type-certified product without being accompanied by an [EASA Form 1](#_DxCrossRefBm1649096870), provided that the installer holds a document issued by the person or organisation that manufactured the part or appliance, which declares the name of the part or appliance, the part number, and the conformity of the part or appliance with its design data, and which contains the issuance date. #### 21.A.307 The eligibility of parts and appliances for installation *Regulation (EU) 2022/1358* (a) A part or appliance is eligible for installation in a type-certified product when it is in a condition for safe operation, marked in accordance with Subpart Q and accompanied by an authorised release certificate ([EASA Form 1](#_DxCrossRefBm485230360)), certifying that the item was manufactured in conformity with approved design data. (b) By way of derogation from point (a) and provided that the conditions in point (c) are met, the following parts or appliances do not require an [EASA Form 1](#_DxCrossRefBm485230360) in order to be eligible for installation in a type-certified product: (1) a standard part; (2) in the case of ELA1 or ELA2, a part or appliance that is: (i) not life limited, nor part of the primary structure, nor part of the flight controls; (ii) identified for installation in the specific aircraft; (iii) to be installed in an aircraft whose owner has verified compliance with the applicable conditions in (i) and (ii), and has accepted responsibility for this compliance; (3) a part or appliance for which the consequences of a non-conformity with its approved design data has a negligible safety effect on the product and which is identified as such by the holder of the design approval in the instructions for continued airworthiness. In order to determine the safety effects of a non-conforming part or appliance, the design approval holder may establish in the instructions for continued airworthiness specific verification activities to be conducted by the installer of the part or appliance on the product; (4) in the case of the embodiment of a standard change in accordance with point [21.A.90B](#_DxCrossRefBm485230522) or a standard repair in accordance with point [21.A.431B](#_DxCrossRefBm485230894), a part or appliance, for which the consequences of a non-conformity with its design data have a negligible safety effect on the product, and which is identified as such in the certification specifications for standard changes and standard repairs issued in accordance with point (a)(2) of point [21.A.90B](#_DxCrossRefBm485230522) and point (a)(2) of point [21.A.431B](#_DxCrossRefBm485230894). In order to determine the safety effects of a non-conforming part or appliance, specific verification activities to be conducted by the person that installs the part or appliance on the product may be established in the certification specifications referred to above; (5) a part or appliance that is exempted from an airworthiness approval in accordance with [Commission Regulation (EU) No 965/2012](https://eur-lex.europa.eu/legal-content/EN/TXT/?uri=CELEX%3A32012R0965&qid=1649401475582) ([[37]](#_ftn37)); and (6) a part or appliance that is an item of a higher assembly identified in points (b)(1) to (b)(5). (7) a part or appliance manufactured by a person or organisation referred to in [Article 9](#_DxCrossRefBm485230359)(4) of this Regulation; (c) Parts and appliances listed in point (b) are eligible for installation in a type-certified product without being accompanied by an [EASA Form 1](#_DxCrossRefBm485230360), provided that the installer holds a document issued by the person or organisation that manufactured the part or appliance, which declares the name of the part or appliance, the part number, and the conformity of the part or appliance with its design data, and which contains the issuance date. --- [[37]](#_ftnref37) Commission Regulation (EU) No 379/2014 of 7 April 2014 amending Commission Regulation (EU) No 965/2012 laying down technical requirements and administrative procedures related to air operations pursuant to Regulation (EC) No 216/2008 of the European Parliament and of the Council ([OJ L 123, 24.4.2014, p. 1](https://eur-lex.europa.eu/legal-content/EN/TXT/?uri=OJ%3AL%3A2014%3A123%3ATOC)).