Appendix 1 to ETSO-C145e A1 - End-Use Equipment Manufacturer Tests for SBAS CCA Functional Position, Velocity, Time (PVT) Sensors Used for Navigation and Non-Navigation Applications

• ED Decision 2020/011/R found in: CS-ETSO Amdt 17 - European Technical Standard Orders (Oct 2026)

###### Appendix 1 to ETSO-C145e A1 – End-Use Equipment Manufacturer Tests for SBAS CCA Functional Position, Velocity, Time (PVT) Sensors Used for Navigation and Non-Navigation Applications *ED Decision 2020/011/R* 1. SCOPE This Appendix describes the required supplementary equipment level testing, in addition to the environmental testing of RTCA document DO-229E, Section 2.4, that is required to be conducted by the manufacturer of the end‑use equipment to receive an ETSO-C145e Class Beta authorisation when using an ETSO-2C204a SBAS CCA functional sensor. To perform functional tests and measure the performance in the environment, the applicant will use the detailed functional test procedures delivered with the ETSO-2C204a CCA. These test procedures are intended to streamline and simplify the ETSO-C145e authorisation process for the manufacturer of the end-use equipment by allowing credit for the design and selected testing performed at the SBAS CCA functional sensor level. However, the manufacturer of the end-use equipment remains fully responsible for the design and control of the article per their ETSO-C145e ETSOA. 2. GENERAL PRINCIPLES (a) Testing methods for GPS/SBAS equipment have been standardised by RTCA document DO-229E, and serve as the basis for ETSO-C145e. RTCA document DO-229E was written to cover equipment that can be installed on aircraft. Section 2.4 specifically addresses the issues of the environment in which the equipment operates and provides the approved test methods to validate the performance of the equipment in this environment. Section 2.4 represents the RTCA consensus in identifying which RTCA document DO-229E requirements are sensitive to environmental effects. These requirements are listed in the environmental tables referenced in Section 2.4.1. (b) The determination that a MOPS requirement is susceptible to the environment does not depend on whether or not the implementation is a CCA installed within an ETSO-C145e article. This is the same concept as an equipment enclosure that is designed to protect against a benign environment compared with one that is designed for a severe environment; the identification of the susceptible requirements is the same. (c) Therefore, this Appendix uses the tables of RTCA document DO-229E Section 2.4.1 to identify the MOPS requirements that are susceptible to environmental effects for an SBAS CCA functional sensor in the end-use equipment. The focus is on the change in environment seen by the SBAS CCA functional sensor as a result of its installation in the end-use equipment. For example, other components inside the end-use equipment may radiate RF energy that could interfere with the GPS functions; therefore, the ambient testing performed at the CCA level is not equivalent to tests performed in the end-use equipment. This is the basis for defining the RTCA document DO-229E Section 2.5 performance tests that need to be repeated by the manufacturer of the end-use equipment. (d) The Class Beta environmental table referenced in RTCA document DO-229E Section 2.4.1 is the prime source to determine the MOPS performance requirements that are susceptible to environmental conditions. Based on the table, the susceptible requirements can be grouped into two categories: those that are susceptible to most types of environmental conditions (described in Section 3) and those that are susceptible to only a few (described in Section 4). Note: The tables for Class Beta-1, -2, and -3 equipment identify similar requirements that are susceptible to the installed environment. The only difference is the applicable MOPS requirements that are consistent with the operational class (i.e. Class -1, - 2, or -3). 3. PERFORMANCE REQUIREMENTS THAT ARE SUSCEPTIBLE TO MOST TYPES OF ENVIRONMENTAL CONDITIONS The RTCA document DO-229E requirements for accuracy (Sections 2.1.3.1, 2.1.4.1, and 2.1.5.1) and sensitivity and dynamic range (Section 2.1.1.10) are sensitive to most types of environmental conditions. However, these requirements are linked to the message loss rate requirement in 2.1.1.3.2. Sections 3.1 and 3.2 below identify the testing that manufacturers of end-use equipment are required to repeat to demonstrate that the SBAS CCA functional sensor continues to meet the accuracy, dynamic range, and message loss rate performance requirements after installation in the end-use equipment. All the tests shall be run under conditions in which the functions of the end-use equipment are fully enabled to create the worst-case environment. 3.1. RTCA document DO-229E — 2.5.8 Accuracy Test (a) The accuracy test described in Section 2.5.8 is actually a joint test that covers accuracy, sensitivity and dynamic range. This joint testing also applies under the environment as stated in Section 2.4.1.1.5, with environmental adaptations as described in Section 2.4.1.1.1. (b) The demonstration of accuracy is performed in accordance with Section 2.5.8.1 only for the test case with broadband external interference noise. This test must be repeated when the CCA is installed in the end-use equipment, and it is sufficient to perform it using broadband interference. (1) The environmental testing is limited to broadband interference, as it represents the worst‑case signal-to-noise condition, which is the most sensitive to environmental effects. This applies equally to the environment for the CCA that is created by the end-use equipment. (2) Section 2.5.8 contains a measurement accuracy test in 2.5.8.1, with the detailed test procedure in Section 2.5.8.2. The Section 2.5.8.1 test must be run under the worst-case environment identified in the ‘Additional Considerations for Internal Interference Sources’ section below. The measurement accuracy testing can be combined with the message loss rate testing described in Section 2.5.2.1. (3) Section 2.5.8.3 is a 24-hour actual satellite accuracy test. The Section 2.5.8.3 test exposes the equipment to a variety of signal conditions and data-processing conditions over varying satellite geometries that will increase the confidence that no unforeseen interactions between components within the end-use equipment and the SBAS CCA functional sensor will go undetected. The 24-hour testing in Section 2.5.8.3 can be combined with the 24‑hour message loss rate testing described in Section 2.5.2.4 (see the section on ‘Additional Considerations for Internal Interference Sources’). (4) Section 2.5.8.4 (SBAS Tracking Bias) is an analysis of the GPS hardware, and it is therefore not necessary to repeat it at the end-use equipment level provided that no extra RF components that affect the RF filtering response are inserted in the RF path. Otherwise, the manufacturer of the end-use equipment must also repeat the SBAS Tracking Bias test. (c) The test threshold is relaxed from 110 % to 125 % as specified in Table 2-25 of the 2.5.8.2.1 test procedure to shorten the duration of the test. However, the Section 2.5.8 testing (excluding the SBAS Tracking Bias test in Section 2.5.8.4) for the CCA in the end-use equipment shall be under ambient conditions per Section 2.5 with the 110-% test pass threshold for the maximum test sensitivity. (d) The Section 2.5.8 testing (excluding the SBAS Tracking Bias test in Section 2.5.8.4) will be repeated against the accuracy requirements that are consistent with the desired operational class (i.e. the Section 2.1.3.1, 2.1.4.1, and 2.1.5.1 accuracy requirements, as appropriate). (e) Only the broadband external interference noise test case using minimum satellite power will be executed in most cases, to shorten the duration of the test. The Section 2.5.8.1 testing will be repeated for both the minimum and the maximum satellite power only for the worst-case environment. 3.2. RTCA document DO-229E — 2.5.2 Message Loss Rate Test (a) Section 2.5.2 specifies the message loss rate test for the Section 2.1.1.3.2 message loss rate requirement. This test is conducted in conjunction with the Section 2.5.8 accuracy testing. Section 2.5.2.2 defines the test procedure to collect data to verify the SBAS message loss rate in the presence of interference using the test cases in which the SBAS satellite is at minimum power. Section 2.5.2.3 defines the pass-fail criteria. (b) The test in Section 2.5.2.2 is performed during the measurement accuracy broadband interference test case described in paragraph 3.1. (c) The test procedure in Section 2.5.2.4.1 is run in conjunction with the Section 2.5.8.3 24-hour accuracy test. Section 2.5.2.4.2 defines the pass-fail criteria for the test case described in paragraph 3.1(b)(3). 4. PERFORMANCE REQUIREMENTS THAT ARE PARTIALLY SUSCEPTIBLE TO ENVIRONMENTAL CONDITIONS (a) The Class Beta tables (Tables 2-14, 2-16, and 2-18) in Section 2.4.1 of RTCA document DO-229E indicate that the requirements for the initial acquisition time (2.1.1.7) and the satellite reacquisition time (2.1.1.9) are sensitive to four environmental conditions: icing, lightning‑induced transient susceptibility, lightning direct effects, and normal/abnormal operating conditions. The requirements for loss of navigation (2.1.1.13.2, 2.1.4.12.2, and 2.1.5.12.2) and loss of integrity (2.1.1.13.1, 2.1.4.12.1, and 2.1.5.12.1) are sensitive to low and high operating temperatures. (b) The lightning-induced transient susceptibility, lightning direct effects, or icing environmental conditions are not pertinent to the environment that is created by the end-use equipment relative to the SBAS CCA functional sensor. However, the manufacturer of the end-use equipment remains responsible for meeting the overall environmental qualification requirements at the end-use equipment level. (c) The loss of navigation and loss of integrity indications are limited to temperature testing, and the information in RTCA document DO-229E, Sections 2.4.1.1.2 and 2.4.1.1.3, is appropriate. The purpose is to ensure that the interface used to indicate the loss of navigation is functional under the environmental conditions that are present after the SBAS CCA functional sensor is installed in the end-use equipment. Sections 2.4.1.1.2 and 2.4.1.1.3 indicate that any source that generates the indication can be used, since it is the interface and not the detection mechanism that is verified. The temperature testing performed at the end-use equipment level is the worst-case scenario. It is not necessary to repeat the CCA-level test at room temperature in the end-use equipment, since the environmental qualification adequately addresses the testing for these requirements. (d) EUROCAE ED-14 Section 16 relates to aircraft power supplies (refer to ETSO Section 3.1.2 for the environmental qualification requirements). Sections 16.5.1.2 and 16.6.1.2 are for supply voltage modulation (AC)/ripple (DC). Given the potential susceptibility of the SBAS CCA functional sensor to power supply noise, it is prudent to repeat the tests at the end-use equipment level on this basis. (e) Sections 4.1 and 4.2 identify the testing that manufacturers of end-use equipment are required to repeat to demonstrate that the SBAS CCA functional sensor continues to meet the acquisition time and reacquisition time performance requirements relative to the normal/abnormal operating conditions after installation in the end-use equipment. All the tests shall be run under conditions in which the functions of the end-use equipment are fully enabled, to create the worst-case environment. 4.1. RTCA document DO-229E — 2.5.4 Initial acquisition test procedures The information in RTCA document DO-229E, Section 2.4.1.1.4, on the initial acquisition test in Section 2.5.4 applies. The manufacturer of the end-use equipment shall repeat the initial acquisition testing described in RTCA DO-229E, Section 2.5.4. 4.2. RTCA document DO-229E — 2.5.6 Satellite reacquisition time test. The manufacturer of the end-use equipment is required to repeat the satellite reacquisition time testing in RTCA document DO-229E, Section 2.5.6. 5. ADDITIONAL CONSIDERATIONS FOR INTERNAL INTERFERENCE SOURCES (a) Installing an SBAS CCA functional sensor into end-use equipment that also includes other functions requires a careful evaluation of the potential internal radiated and conducted interference. The manufacturer of the end-use equipment must evaluate each operating mode to determine whether the mode changes the environment for the installed SBAS CCA functional sensor. If there is only one environment, or there is clearly one worst-case environment, then the accuracy and message loss rate testing in Section 3 can be run in that operating mode only. For example, if the end-use equipment includes an RF transmitter that radiates at one frequency, one could reasonably argue that setting the transmitter at full power with maximum data throughput would generate a clear worst-case environment in which to run all the testing. (b) In the case of multiple environments, the accuracy and message loss rate tests can either be run in each environment, or the methodology in RTCA document DO-229E, Section 2.4.1.2.3, can be used to run an aggregate test with approximately equal time in each mode. The methodology in Section 2.4.1.2.3 must be used to identify the modes with the greatest susceptibility under which the combined accuracy and message loss rate tests are repeated in addition to the aggregate test. For example, the methodology of Section 2.4.1.2.3 is appropriate for end-use equipment that contains a high-power transmitter that operates on a large number of frequencies such that it is impractical to run a test at each frequency. This is analogous to the large number of frequencies that need to be tested during the EUROCAE ED-14 Section 19 testing on induced signal susceptibility and the Section 20 testing on radio frequency susceptibility, and this is the reason why the methodology of Section 2.4.1.2.3 was developed. (c) It is sufficient to identify one worst-case environment when performing acquisition and 24-hour accuracy testing. 6. SUMMARY (a) The manufacturer of end-use equipment that incorporates an SBAS CCA functional sensor is required to repeat the following RTCA document DO-229E Section 2.5 testing under ambient conditions (see Section 5) after installing the SBAS CCA functional sensor in the end-use equipment: — The Section 2.5.8 accuracy test (excluding the SBAS Tracking Bias test in 2.5.8.4) adapted per Section 2.4.1.1.1, except that the 110-% test pass threshold is used. — Note: Excluding the SBAS Tracking Bias test is acceptable, provided that the end-use equipment does not insert into the RF signal path any components that affect the filtering response. Otherwise, the manufacturer of the end-use equipment must repeat the SBAS Tracking Bias test as well. — The Section 2.5.2 message loss rate test. — The Section 2.5.4 initial acquisition test. — The Section 2.5.6 satellite reacquisition time test. (b) The manufacturer of the end-use equipment remains responsible for completing a full environmental qualification evaluation (ETSO Section 3.1.2) at the end‑use equipment level. The manufacturer of end-use equipment that incorporates an SBAS CCA functional sensor is required to repeat the loss of navigation indication and loss of integrity indication tests as part of the environmental qualification according to RTCA document DO-229E Sections 2.4.1.1.2 and 2.4.1.1.3 respectively. [Amdt ETSO/13] [Amdt ETSO/16]