AMC1
ML.A.801 Aircraft certificate of release to service
ED
Decision 2020/002/R
AIRCRAFT CERTIFICATE OF RELEASE TO SERVICE (CRS) AFTER EMBODIMENT OF A STANDARD CHANGE OR A STANDARD REPAIR (SC/SR)
1. Release
to service and eligible persons
Only natural
or legal persons entitled to release to service an aircraft after maintenance
(see ML.A.801(b)) are considered as an eligible installer
responsible for the embodiment of a SC/SR when in compliance with applicable
requirements.
Since the
design of the SC/SR does not require specific approval, the natural or legal
person releasing the embodiment of the change or repair takes the
responsibility that the applicable certification specifications within CS-STAN
are fulfilled while being in compliance with Part-ML/ Part-M Subpart
F/Part-CAO and/or Part-145 and not in conflict with the TC holder’s data. This
includes responsibility in respect of an adequate design, the
selection/manufacturing of suitable parts and their identification, documenting
the change or repair, generation or amendment of aircraft manuals and
instructions as needed, embodiment of the change/repair, releasing the
aircraft to service and record-keeping.
Depending on
its nature, for certain SCs/SRs, CS-STAN might restrict the eligibility for
the issuance of the release to service to certain persons (e.g. standard
change/repair not suitable for release to service by the pilot-owner).
NOTE: Until
1 October 2020 (ref. entry into force of Commission Regulation (EU)
2018/1142), it is possible to have aircraft maintenance released to service by
the holder of an appropriate certifying staff qualification valid in a Member
State (national qualification). In this case, the following conditions apply:
-
If
the holder signs the release to service on behalf of a maintenance
organisation, this release is valid regardless of the Member State where the
aircraft is registered.
-
If
the holder signs the release to service as an independent certifying staff,
this release is only valid in the Member State responsible for such certifying
staff qualification and where the aircraft is registered.
2. Parts
and appliances to be installed as part of a SC/SR
The design
of the parts and appliances to be used in a SC/SR is considered a part of the
change/repair, and, therefore, there is no need of a specific design approval.
However, it is possible that for a particular SC, these certification
specifications specifically require the use of parts and appliances that meet
a technical standard. In this case, when the parts and appliances are required
to be authorised as an ETSO article, other articles recognised as equivalent
by means of an international safety agreement or grandfathered in accordance
with Regulation (EU) No 748/2012 are equally acceptable.
Normally, a
SC/SR shall not contain specifically designed parts that should be produced by
a production organisation approved in accordance with Part 21 (POA). However,
in the case that the change or repair would contain such a part, it should be
produced by an approved production organisation (POA holder), and delivered
with an EASA Form 1. An arrangement in accordance with 21.A.122(b) is not
applicable.
Eligibility
for installation of parts and appliances belonging to a SC/SR is subject to
compliance with the Part 21 and Part-ML and maintenance-organisation-related
provisions, and the situation varies depending on the aircraft in/on which the
SC/SR is to be embodied, and who the installer is. The need for an EASA Form 1
is addressed in Part 21 and Part-ML, while less restrictive rules may, for
instance, apply for ELA1 and ELA2 aircraft parts (e.g. 21.A.307) and sailplane
parts (e.g. AMC 21.A.303 of the ‘AMC and GM to Part 21’). Furthermore, Part-M
Subpart F, Part-CAO and Part-145 contain provisions (i.e. M.A.603(c), CAO.A.020(c) and 145.A.42(c)) that allow maintenance
organisations to fabricate certain parts to be installed in/on the aircraft as
part of their maintenance activities.
3. Parts’
and appliances’ identification
The parts
modified or installed during the embodiment of the SC/SR need to be
permanently marked in accordance with Part 21 Subpart Q.
4. Documenting
the SC/SR and declaring compliance with the certification specifications
In
accordance with Part-ML, Part-M Subpart F, Part-CAO or Part-145 (e.g. ML.A.801(e),
M.A.612, CAO.A.065 and 145.A.50(b)), the legal or natural person
responsible for the embodiment of a change or a repair should compile details
of the work accomplished. In the case of SCs/SRs, this includes, as necessary,
based on the complexity, an engineering file containing drawings, a list of
the parts and appliances used for the change or repair, supporting analysis
and the results of tests performed or any other evidence suitable to show that
the design fulfils the applicable certification specifications within CS-STAN
together with a statement of compliance and amendments to aircraft manuals, to
instructions for continuing airworthiness and to other documents such as
aircraft parts list, wiring diagrams, etc. as deemed necessary. The EASA Form
123 is prepared for the purpose of documenting the preparation and embodiment
of the SC/SR. The aircraft logbook should contain an entry referring to EASA
Form 123; both EASA Form 123 and the release to service required after the
embodiment of the SC/SR should be signed by the same person.
EASA Form
123 and all the records listed on it should follow elementary principles of
controlled documentation, e.g. contain reference number of documents, issue
dates, revision numbers, name of persons preparing/releasing the document,
etc.
5. Record-keeping
The legal or
natural person responsible (see paragraph 1. above) for the embodiment of the
change/repair should keep the records generated with the SC/SR as required by
Part-ML, Part-M Subpart F, Part-CAO or Part-145 and CS-STAN.
In addition,
ML.A.305 requires that the aircraft owner (or CAMO or CAO, if a contract in
accordance with ML.A.201 exists) keeps the status of the changes/repairs
embodied in/on the aircraft in order to control the aircraft configuration and
manage its continuing airworthiness.
With regard
to SCs/SRs, the information provided to the owner, CAMO or CAO may be listed
in EASA Form 123 and should include, as required, a copy of any modified
aircraft manual and/or instructions for continuing airworthiness. All this
information should normally be consulted when the aircraft undergoes an AR,
and, therefore, a clear system to record the embodiment of SCs/SRs, which is
also easily traceable, would be of help during subsequent aircraft
inspections.
6. Instructions
for continuing airworthiness (ICA)
As
stipulated in ML.A.302, the aircraft owner, CAMO or CAO
needs to assess if the changes in the ICA of the aircraft require the
amendment of the AMP.
7. Embodiment
of more than one SC
The
embodiment of two or more related SCs described in Subpart B of CS-STAN is
permitted as a single change (the use of one EASA Form 123 only) as long as
adequate references to and records of all SCs embodied are captured.
Restrictions and limitations of the two (or more) SCs would apply. It is
permitted to issue a single release to service containing adequate
traceability of all the SCs embodied.
8. Acceptable
form to be used to record the embodiment of SCs/SRs
See EASA Form 123.
EASA Form 123 — Standard Change/Standard
Repair (SC/SR) embodiment record
|
EASA Form 123 — Standard Change/Standard Repair (SC/SR) embodiment record |
1. SC/SR number(s): |
|
|
2. SC/SR title & description: |
||
|
|
||
|
3. Applicability: |
||
|
4. List of parts (description/Part-No/Qty): |
||
|
5. Operational limitations/affected aircraft manuals. Copies of these manuals are provided to the aircraft owner: |
||
|
6. Documents used for the development and embodiment of this SC/SR: |
||
|
* Copies of the documents marked with an asterisk are handed to the aircraft owner. |
||
|
7. Instructions for continuing airworthiness. Copies of these manuals are provided to the aircraft owner: |
||
|
8. Other information: |
||
|
9a. This SC complies with the criteria established in 21.A.90B(a) and with the relevant paragraphs of CS-STAN. |
||
|
9b. This SR complies with the criteria established in 21.A.431B(a) and with the relevant paragraphs of CS-STAN. |
||
|
10. Date of SC/SR embodiment: |
11. Identification data and signature of the person responsible for the embodiment of the SC/SR: |
|
|
|
|
|
|
12. Signature of the aircraft owner. This signature attests that all relevant documentation is handed over from the issuer of this form to the aircraft owner, and, therefore, the latter becomes aware of any impact or limitations on operations or additional continuing airworthiness requirements which may apply to the aircraft due to the embodiment of the change/repair. |
||
Form 123
Issue 00
Notes:
Original
remains with the legal or natural person responsible for the embodiment of the
SC/SR.
The
aircraft owner should retain a copy of this form.
The
aircraft owner should be provided with copies of the documents referenced in
boxes 5 and 7 and those in box 6 marked with an asterisk ‘*’.
The
‘relevant paragraphs’ in boxes 9a and 9b refer to the applicable paragraphs of
‘Subpart A – General’ of CS-STAN and those of the SC/SR quoted in box 2.
For box
12, when the aircraft owner has signed a contract in accordance with ML.A.201,
it is possible that the CAMO or CAO representative signs box 12 and provides
all relevant information to the owner before next flight.
Completion
instructions:
Use
English or the official language of the State of registry to fill in the form.
1. Identify
the SC/SR with a unique number and reference this number in the aircraft
logbook.
2. Specify
the applicable EASA CS-STAN chapter including revision (e.g. CS-SCxxxy or
CS-SRxxxy) & title. Provide also a short description.
3. Identify
the aircraft (a/c) registration, serial number and type.
4. List
the parts' numbers and description for the parts installed. Refer to an
auxiliary document if necessary.
5. Identify
affected aircraft manuals.
6. Refer
to the documentation developed to support the SC/SR and its embodiment,
including design data required by CS-STAN: design definition, documents
recording the showing of compliance with the certification specifications or
any test result, etc. The documents' references should quote their
revision/issue.
7. Identify
instructions for continuing airworthiness that need to be considered for the
aircraft maintenance programme review.
8. To
be used as deemed necessary by the installer.
9a., 9b., 10. and 12.
Self-explanatory.
11. Give full name details and certificate reference (of the natural or legal person) used for issuing the aircraft release to service.
EASA regulations detail aircraft release to service after standard changes/repairs. Qualified personnel ensure compliance with certification specifications, documenting work via EASA Form 123. Parts must be identified, and records maintained. Owners receive documentation impacting airworthiness. Multiple changes can be a single release if traceable.
* Summary by Aviation.Bot - Always consult the original document for the most accurate information.
Loading collections...