Appendix A: Groups, Major Topics, Standardised Sequence and Description of Minimum Content

• ED Decision 2008/007/R found in: AMC-20 Amdt 23 - Airworthiness of Products, Parts and Appliances (Jan 2022)

Appendix A: Groups, Major Topics, Standardised Sequence and Description of Minimum Content ED Decision 2008/007/R <table border="1" cellpadding="0" cellspacing="0" width="607"> <thead> <tr> <td valign="top" width="109"> <p><b>GROUP</b></p> </td> <td valign="top" width="178"> <p><b>MAJOR TOPIC</b></p> </td> <td valign="top" width="319"> <p><b>DESCRIPTION</b></p> </td> </tr> </thead> <tr> <td rowspan="5" width="109"> <p>GENERAL DATA</p> </td> <td width="178"> <p>SAFETY PRACTICES</p> </td> <td width="319"> <p>Safety regulations and general safety precautions to prevent injury to personnel and damage to the airplane</p> </td> </tr> <tr> <td width="178"> <p>AIRPLANE ENVIRONMENTAL AREAS</p> </td> <td width="319"> <p>Definition of types of areas upon which wiring configuration and wiring component selection is constrained</p> </td> </tr> <tr> <td width="178"> <p>CONSUMABLE MATERIALS</p> </td> <td width="319"> <p>Wiring maintenance processing materials (solvents, aqueous cleaners, lubricants, etc.)</p> </td> </tr> <tr> <td width="178"> <p>WIRING MATERIALS</p> </td> <td width="319"> <p>Materials that become an integral part of the wiring configuration excluding wire and cable, e.g., sleeves, shield material, tie material, sealants, etc.</p> </td> </tr> <tr> <td width="178"> <p>COMMON TOOLS</p> </td> <td width="319"> <p>Description and operation of common tools</p> </td> </tr> <tr> <td rowspan="6" width="109"> <p>EWIS MAINTENANCE</p> </td> <td width="178"> <p>EWIS PROTECTION DURING MAINTENANCE</p> </td> <td width="319"> <p>Procedures to protect EWIS during airplane maintenance and modification</p> </td> </tr> <tr> <td width="178"> <p>EWIS CLEANING</p> </td> <td width="319"> <p>In support of inspection as well as prevention of degradation and preparation for repair; recommended cleaning materials and procedures based on type of contamination</p> </td> </tr> <tr> <td width="178"> <p>EWIS INSPECTION</p> </td> <td width="319"> <p>Criteria for correct installation, correct wiring assembly configuration; damage conditions and limits for wiring components (wire and cable, termination types, electrical devices); factors that warrant disassembly for inspection; determination of cause of damage</p> </td> </tr> <tr> <td width="178"> <p>EWIS TESTING</p> </td> <td width="319"> <p>Wiring integrity testing</p> </td> </tr> <tr> <td width="178"> <p>EWIS DISASSEMBLY</p> </td> <td width="319"> <p>Data and procedures in support of inspection, cleaning when applicable; also supports new wiring installation</p> </td> </tr> <tr> <td width="178"> <p>EWIS REPAIR AND REPLACEMENT</p> </td> <td width="319"> <p>Repair of wiring installation, wiring assembly configuration, wiring components (wire and cable, wiring terminations, electrical devices); wire and cable replacement; wiring functional identification</p> </td> </tr> <tr> <td rowspan="3" width="109"> <p>WIRING INSTALLATION</p> </td> <td width="178"> <p>WIRE SEPARATION/ SEGREGATION</p> </td> <td width="319"> <p>Explanation of separation/segregation categories, separation/segregation identification, and necessary conditions for maintaining separation/segregation</p> </td> </tr> <tr> <td width="178"> <p>ELECTRICAL BONDS AND GROUNDS</p> </td> <td width="319"> <p>Bond surface preparation, ground hardware configurations, bond integrity testing</p> </td> </tr> <tr> <td width="178"> <p>WIRE HARNESS INSTALLATION</p> </td> <td width="319"> <p>Routing, supports; wiring protection, factors affecting wiring assembly configuration; connection to equipment, new wiring, removal from service</p> </td> </tr> <tr> <td rowspan="5" width="109"> <p>WIRING ASSEMBLY</p> </td> <td width="178"> <p>WIRE AND CABLE TYPES</p> </td> <td width="319"> <p>The principal material component of airplane wiring; includes type identification and basic description; alternative wire types (replacements, substitutions)</p> </td> </tr> <tr> <td width="178"> <p>WIRE MARKING</p> </td> <td width="319"> <p>Marking; applicable conditions</p> </td> </tr> <tr> <td width="178"> <p>WIRE HARNESS ASSEMBLY</p> </td> <td width="319"> <p>Wiring assembly configuration: Assembly materials, layout, overall protection; factors affecting wiring installation</p> </td> </tr> <tr> <td width="178"> <p>WIRE INSULATION AND CABLE JACKET REMOVAL</p> </td> <td width="319"> <p>Wire and cable: Insulation removal, jacket removal; associated damage limits, tool description and operation</p> </td> </tr> <tr> <td width="178"> <p>&lt;&lt;TERMINATION TYPE&gt;&gt;<br/> e.g., SOURIAU 8950 SERIES CONNECTORS</p> </td> <td width="319"> <p>Wiring terminations and accessories (connectors, terminal lugs, splices, backshells, etc.) grouped by termination type from simple to complex:</p> <p>a.      Common data or procedures by group (if any), e.g., tool description and operation, definition of internal damage and limits, internal cleaning, accessories</p> <p>b.      By individual type - part numbers and description, definition of internal damage and limits (if not specified by common data), disassembly, assembly, installation</p> </td> </tr> <tr> <td width="109"> <p>ELECTRICAL DEVICES</p> </td> <td width="178"> <p>&lt;&lt;DEVICE TYPE&gt;&gt;<br/> e.g., KLIXON 7274 SERIES CIRCUIT BREAKER</p> </td> <td width="319"> <p>Electrical devices (circuit breakers, relays, switches, filters, lamps, etc.) grouped by device type:</p> <p>a.      Common data or procedures by group (if any), e.g., tool description and operation, definition of internal damage and limits, internal cleaning, accessories</p> <p>b.      By individual type - part numbers and description, definition of internal damage and limits (if not specified by common data), disassembly, assembly, installation</p> </td> </tr> <tr> <td width="109"> <p>SPECIFIC SYSTEM WIRING</p> </td> <td width="178"> <p>SPECIFIC WIRING ASSEMBLY</p> </td> <td width="319"> <p>For wiring that has a necessarily specific configuration (e.g. Primary Flight Control, Fuel Quantity Indicator System, etc.):</p> <p>– Applicable conditions for repair and replacement</p> <p>– Disassembly, assembly, installation, assembly integrity testing</p> </td> </tr> <tr> <td width="109"> <p>AIRLINE CUSTOMISED DATA</p> </td> <td width="178"> <p>AIRLINE SPECIFIED</p> </td> <td width="319"> <p>Reserved for airline use</p> </td> </tr> </table> [Amdt 20/4] Appendix A: Groups, Major Topics, Standardised Sequence and Description of Minimum Content ED Decision 2008/007/R <table border="1" cellpadding="0" cellspacing="0" width="607"><thead><tr><td valign="top" width="109"><p><b>GROUP</b></p></td><td valign="top" width="178"><p><b>MAJOR TOPIC</b></p></td><td valign="top" width="319"><p><b>DESCRIPTION</b></p></td></tr></thead><tr><td rowspan="5" width="109"><p>GENERAL DATA</p></td><td width="178"><p>SAFETY PRACTICES</p></td><td width="319"><p>Safety regulations and general safety precautions to prevent injury to personnel and damage to the airplane</p></td></tr><tr><td width="178"><p>AIRPLANE ENVIRONMENTAL AREAS</p></td><td width="319"><p>Definition of types of areas upon which wiring configuration and wiring component selection is constrained</p></td></tr><tr><td width="178"><p>CONSUMABLE MATERIALS</p></td><td width="319"><p>Wiring maintenance processing materials (solvents, aqueous cleaners, lubricants, etc.)</p></td></tr><tr><td width="178"><p>WIRING MATERIALS</p></td><td width="319"><p>Materials that become an integral part of the wiring configuration excluding wire and cable, e.g., sleeves, shield material, tie material, sealants, etc.</p></td></tr><tr><td width="178"><p>COMMON TOOLS</p></td><td width="319"><p>Description and operation of common tools</p></td></tr><tr><td rowspan="6" width="109"><p>EWIS MAINTENANCE</p></td><td width="178"><p>EWIS PROTECTION DURING MAINTENANCE</p></td><td width="319"><p>Procedures to protect EWIS during airplane maintenance and modification</p></td></tr><tr><td width="178"><p>EWIS CLEANING</p></td><td width="319"><p>In support of inspection as well as prevention of degradation and preparation for repair; recommended cleaning materials and procedures based on type of contamination</p></td></tr><tr><td width="178"><p>EWIS INSPECTION</p></td><td width="319"><p>Criteria for correct installation, correct wiring assembly configuration; damage conditions and limits for wiring components (wire and cable, termination types, electrical devices); factors that warrant disassembly for inspection; determination of cause of damage</p></td></tr><tr><td width="178"><p>EWIS TESTING</p></td><td width="319"><p>Wiring integrity testing</p></td></tr><tr><td width="178"><p>EWIS DISASSEMBLY</p></td><td width="319"><p>Data and procedures in support of inspection, cleaning when applicable; also supports new wiring installation</p></td></tr><tr><td width="178"><p>EWIS REPAIR AND REPLACEMENT</p></td><td width="319"><p>Repair of wiring installation, wiring assembly configuration, wiring components (wire and cable, wiring terminations, electrical devices); wire and cable replacement; wiring functional identification</p></td></tr><tr><td rowspan="3" width="109"><p>WIRING INSTALLATION</p></td><td width="178"><p>WIRE SEPARATION/ SEGREGATION</p></td><td width="319"><p>Explanation of separation/segregation categories, separation/segregation identification, and necessary conditions for maintaining separation/segregation</p></td></tr><tr><td width="178"><p>ELECTRICAL BONDS AND GROUNDS</p></td><td width="319"><p>Bond surface preparation, ground hardware configurations, bond integrity testing</p></td></tr><tr><td width="178"><p>WIRE HARNESS INSTALLATION</p></td><td width="319"><p>Routing, supports; wiring protection, factors affecting wiring assembly configuration; connection to equipment, new wiring, removal from service</p></td></tr><tr><td rowspan="5" width="109"><p>WIRING ASSEMBLY</p></td><td width="178"><p>WIRE AND CABLE TYPES</p></td><td width="319"><p>The principal material component of airplane wiring; includes type identification and basic description; alternative wire types (replacements, substitutions)</p></td></tr><tr><td width="178"><p>WIRE MARKING</p></td><td width="319"><p>Marking; applicable conditions</p></td></tr><tr><td width="178"><p>WIRE HARNESS ASSEMBLY</p></td><td width="319"><p>Wiring assembly configuration: Assembly materials, layout, overall protection; factors affecting wiring installation</p></td></tr><tr><td width="178"><p>WIRE INSULATION AND CABLE JACKET REMOVAL</p></td><td width="319"><p>Wire and cable: Insulation removal, jacket removal; associated damage limits, tool description and operation</p></td></tr><tr><td width="178"><p>&lt;&lt;TERMINATION TYPE&gt;&gt;<br/> e.g., SOURIAU 8950 SERIES CONNECTORS</p></td><td width="319"><p>Wiring terminations and accessories (connectors, terminal lugs, splices, backshells, etc.) grouped by termination type from simple to complex:</p><p>a. Common data or procedures by group (if any), e.g., tool description and operation, definition of internal damage and limits, internal cleaning, accessories</p><p>b. By individual type - part numbers and description, definition of internal damage and limits (if not specified by common data), disassembly, assembly, installation</p></td></tr><tr><td width="109"><p>ELECTRICAL DEVICES</p></td><td width="178"><p>&lt;&lt;DEVICE TYPE&gt;&gt;<br/> e.g., KLIXON 7274 SERIES CIRCUIT BREAKER</p></td><td width="319"><p>Electrical devices (circuit breakers, relays, switches, filters, lamps, etc.) grouped by device type:</p><p>a. Common data or procedures by group (if any), e.g., tool description and operation, definition of internal damage and limits, internal cleaning, accessories</p><p>b. By individual type - part numbers and description, definition of internal damage and limits (if not specified by common data), disassembly, assembly, installation</p></td></tr><tr><td width="109"><p>SPECIFIC SYSTEM WIRING</p></td><td width="178"><p>SPECIFIC WIRING ASSEMBLY</p></td><td width="319"><p>For wiring that has a necessarily specific configuration (e.g. Primary Flight Control, Fuel Quantity Indicator System, etc.):</p><p>– Applicable conditions for repair and replacement</p><p>– Disassembly, assembly, installation, assembly integrity testing</p></td></tr><tr><td width="109"><p>AIRLINE CUSTOMISED DATA</p></td><td width="178"><p>AIRLINE SPECIFIED</p></td><td width="319"><p>Reserved for airline use</p></td></tr></table> [Amdt 20/4] Appendix A: Groups, Major Topics, Standardised Sequence and Description of Minimum Content ED Decision 2008/007/R <table border="1" cellpadding="0" cellspacing="0" width="607"> <thead> <tr> <td valign="top" width="109"> <p><b>GROUP</b></p> </td> <td valign="top" width="178"> <p><b>MAJOR TOPIC</b></p> </td> <td valign="top" width="319"> <p><b>DESCRIPTION</b></p> </td> </tr> </thead> <tr> <td rowspan="5" width="109"> <p>GENERAL DATA</p> </td> <td width="178"> <p>SAFETY PRACTICES</p> </td> <td width="319"> <p>Safety regulations and general safety precautions to prevent injury to personnel and damage to the airplane</p> </td> </tr> <tr> <td width="178"> <p>AIRPLANE ENVIRONMENTAL AREAS</p> </td> <td width="319"> <p>Definition of types of areas upon which wiring configuration and wiring component selection is constrained</p> </td> </tr> <tr> <td width="178"> <p>CONSUMABLE MATERIALS</p> </td> <td width="319"> <p>Wiring maintenance processing materials (solvents, aqueous cleaners, lubricants, etc.)</p> </td> </tr> <tr> <td width="178"> <p>WIRING MATERIALS</p> </td> <td width="319"> <p>Materials that become an integral part of the wiring configuration excluding wire and cable, e.g., sleeves, shield material, tie material, sealants, etc.</p> </td> </tr> <tr> <td width="178"> <p>COMMON TOOLS</p> </td> <td width="319"> <p>Description and operation of common tools</p> </td> </tr> <tr> <td rowspan="6" width="109"> <p>EWIS MAINTENANCE</p> </td> <td width="178"> <p>EWIS PROTECTION DURING MAINTENANCE</p> </td> <td width="319"> <p>Procedures to protect EWIS during airplane maintenance and modification</p> </td> </tr> <tr> <td width="178"> <p>EWIS CLEANING</p> </td> <td width="319"> <p>In support of inspection as well as prevention of degradation and preparation for repair; recommended cleaning materials and procedures based on type of contamination</p> </td> </tr> <tr> <td width="178"> <p>EWIS INSPECTION</p> </td> <td width="319"> <p>Criteria for correct installation, correct wiring assembly configuration; damage conditions and limits for wiring components (wire and cable, termination types, electrical devices); factors that warrant disassembly for inspection; determination of cause of damage</p> </td> </tr> <tr> <td width="178"> <p>EWIS TESTING</p> </td> <td width="319"> <p>Wiring integrity testing</p> </td> </tr> <tr> <td width="178"> <p>EWIS DISASSEMBLY</p> </td> <td width="319"> <p>Data and procedures in support of inspection, cleaning when applicable; also supports new wiring installation</p> </td> </tr> <tr> <td width="178"> <p>EWIS REPAIR AND REPLACEMENT</p> </td> <td width="319"> <p>Repair of wiring installation, wiring assembly configuration, wiring components (wire and cable, wiring terminations, electrical devices); wire and cable replacement; wiring functional identification</p> </td> </tr> <tr> <td rowspan="3" width="109"> <p>WIRING INSTALLATION</p> </td> <td width="178"> <p>WIRE SEPARATION/ SEGREGATION</p> </td> <td width="319"> <p>Explanation of separation/segregation categories, separation/segregation identification, and necessary conditions for maintaining separation/segregation</p> </td> </tr> <tr> <td width="178"> <p>ELECTRICAL BONDS AND GROUNDS</p> </td> <td width="319"> <p>Bond surface preparation, ground hardware configurations, bond integrity testing</p> </td> </tr> <tr> <td width="178"> <p>WIRE HARNESS INSTALLATION</p> </td> <td width="319"> <p>Routing, supports; wiring protection, factors affecting wiring assembly configuration; connection to equipment, new wiring, removal from service</p> </td> </tr> <tr> <td rowspan="5" width="109"> <p>WIRING ASSEMBLY</p> </td> <td width="178"> <p>WIRE AND CABLE TYPES</p> </td> <td width="319"> <p>The principal material component of airplane wiring; includes type identification and basic description; alternative wire types (replacements, substitutions)</p> </td> </tr> <tr> <td width="178"> <p>WIRE MARKING</p> </td> <td width="319"> <p>Marking; applicable conditions</p> </td> </tr> <tr> <td width="178"> <p>WIRE HARNESS ASSEMBLY</p> </td> <td width="319"> <p>Wiring assembly configuration: Assembly materials, layout, overall protection; factors affecting wiring installation</p> </td> </tr> <tr> <td width="178"> <p>WIRE INSULATION AND CABLE JACKET REMOVAL</p> </td> <td width="319"> <p>Wire and cable: Insulation removal, jacket removal; associated damage limits, tool description and operation</p> </td> </tr> <tr> <td width="178"> <p>&lt;&lt;TERMINATION TYPE&gt;&gt;<br/> e.g., SOURIAU 8950 SERIES CONNECTORS</p> </td> <td width="319"> <p>Wiring terminations and accessories (connectors, terminal lugs, splices, backshells, etc.) grouped by termination type from simple to complex:</p> <p>a.      Common data or procedures by group (if any), e.g., tool description and operation, definition of internal damage and limits, internal cleaning, accessories</p> <p>b.      By individual type - part numbers and description, definition of internal damage and limits (if not specified by common data), disassembly, assembly, installation</p> </td> </tr> <tr> <td width="109"> <p>ELECTRICAL DEVICES</p> </td> <td width="178"> <p>&lt;&lt;DEVICE TYPE&gt;&gt;<br/> e.g., KLIXON 7274 SERIES CIRCUIT BREAKER</p> </td> <td width="319"> <p>Electrical devices (circuit breakers, relays, switches, filters, lamps, etc.) grouped by device type:</p> <p>a.      Common data or procedures by group (if any), e.g., tool description and operation, definition of internal damage and limits, internal cleaning, accessories</p> <p>b.      By individual type - part numbers and description, definition of internal damage and limits (if not specified by common data), disassembly, assembly, installation</p> </td> </tr> <tr> <td width="109"> <p>SPECIFIC SYSTEM WIRING</p> </td> <td width="178"> <p>SPECIFIC WIRING ASSEMBLY</p> </td> <td width="319"> <p>For wiring that has a necessarily specific configuration (e.g. Primary Flight Control, Fuel Quantity Indicator System, etc.):</p> <p>– Applicable conditions for repair and replacement</p> <p>– Disassembly, assembly, installation, assembly integrity testing</p> </td> </tr> <tr> <td width="109"> <p>AIRLINE CUSTOMISED DATA</p> </td> <td width="178"> <p>AIRLINE SPECIFIED</p> </td> <td width="319"> <p>Reserved for airline use</p> </td> </tr> </table> [Amdt 20/4]