Appendix A to AMC 20-22 - EWIS Minimum Initial Training Programme for Group 1 and 2

• ED Decision 2008/007/R found in: AMC-20 Amdt 22 - Airworthiness of Products, Parts and Appliances (May 2021)

Appendix A to AMC 20-22 – EWIS Minimum Initial Training Programme for Group 1 and 2 ED Decision 2008/007/R Target Group 1: Qualified staff performing EWIS maintenance. Target Group 2: Qualified staff performing maintenance inspections on EWIS. <table border="1" cellpadding="0" cellspacing="0" width="604"><tr><td valign="top" width="510"><p><b>TARGET GROUP</b></p></td><td valign="top" width="47"><p><b>1</b></p></td><td valign="top" width="47"><p><b>2</b></p></td></tr><tr><td valign="bottom" width="510"><p>A – GENERAL ELECTRICAL WIRING INTERCONNECTION SYSTEM PRACTICES</p><p>Know or demonstrate safe handling of aeroplane electrical systems, line replaceable units (LRU), tooling, troubleshooting procedures, and electrical measurement.</p></td><td valign="top" width="47"></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>1. Safety practices</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>2. Electrostatic discharge sensitive (ESDS) device handling and protection</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>3. Tools, special tools, and equipment</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>4. Verifying calibration/certification of instruments, tools, and equipment</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>5. Required wiring checks using the troubleshooting procedures and charts</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>6. Measurement and troubleshooting using meters</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>7. LRU replacement general practices</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="bottom" width="510"><p>B – WIRING PRACTICES DOCUMENTATION</p><p>Know or demonstrate the construction and navigation of the applicable aeroplane wiring system overhaul or practices manual.</p></td><td valign="top" width="47"></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>8. Standard wiring practices manual structure/overview</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>9. Chapter cross-reference index</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>10. Important data and tables</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>11. Wiring diagram manuals</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>12. Other documentation as applicable</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="bottom" width="510"><p>C – INSPECTION</p><p>Know the different types of inspections, human factors in inspections, zonal areas and typical damages.</p></td><td valign="top" width="47"></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>13. General visual inspection (GVI), detailed inspection (DET), special detailed inspection (SDI), and zonal inspection, and their criteria and standards</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>14. Human factors in inspection</p></td><td valign="top" width="47"></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>15. Zonal areas of inspection</p></td><td valign="top" width="47"></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>16. Wiring system damage</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="bottom" width="510"><p>D – HOUSEKEEPING</p><p>Know the contamination sources, materials, cleaning and protection procedures.</p></td><td valign="top" width="47"></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>17. Aeroplane external contamination sources</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>18. Aeroplane internal contamination sources</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>19. Other contamination sources</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>20. Contamination protection planning</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>21. Protection during aeroplane maintenance and repair</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>22. Cleaning processes</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="bottom" width="510"><p>E – WIRE</p><p>Know or demonstrate the correct identification of different wire types, their inspection criteria and damage tolerance, repair and preventative maintenance procedures.</p></td><td valign="top" width="47"></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>23. Wire identification, type and construction</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>24. Insulation qualities and damage limits</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>25. Inspection criteria and standards for wire and wire bundles</p></td><td valign="top" width="47"></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>26. Wire bundle installation practices</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>27. Typical damage and areas found (aeroplane specific)</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>28. Maintenance and repair procedures</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>29. Sleeving</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>30. Unused wires - termination and storage</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>31. Electrical bonding and grounds</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="bottom" width="510"><p>F – CONNECTIVE DEVICES</p><p>Know or demonstrate the procedures to identify, inspect, and find the correct repair for typical types of connective devices found on the applicable aeroplane.</p></td><td valign="top" width="47"></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>32. General connector types and identification</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>33. Cautions and protections</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>34. Visual inspection procedures</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>35. Typical damage found</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="top" width="510"><p>36. Repair procedures</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"><p>X</p></td></tr><tr><td valign="bottom" width="510"><p>G – CONNECTIVE DEVICE REPAIR</p><p>Demonstrate the procedures for replacement of all parts of typical types of connectors found on the applicable aeroplane.</p></td><td valign="top" width="47"></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>37. Circular connectors</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>38. Rectangular connectors</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>39. Terminal blocks - modular</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>40. Terminal blocks - non-modular</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>41. Grounding modules</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr><tr><td valign="top" width="510"><p>42. Pressure seals</p></td><td valign="top" width="47"><p>X</p></td><td valign="top" width="47"></td></tr></table> [Amdt 20/4] Appendix A to AMC 20-22 – EWIS Minimum Initial Training Programme for Group 1 and 2 ED Decision 2008/007/R Target Group 1: Qualified staff performing EWIS maintenance. Target Group 2: Qualified staff performing maintenance inspections on EWIS. <table border="1" cellpadding="0" cellspacing="0" width="604"> <tr> <td valign="top" width="510"> <p><b>TARGET GROUP</b></p> </td> <td valign="top" width="47"> <p><b>1</b></p> </td> <td valign="top" width="47"> <p><b>2</b></p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>A – GENERAL ELECTRICAL WIRING INTERCONNECTION SYSTEM PRACTICES</p> <p>Know or demonstrate safe handling of aeroplane electrical systems, line replaceable units (LRU), tooling, troubleshooting procedures, and electrical measurement.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>1.         Safety practices</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>2.         Electrostatic discharge sensitive (ESDS) device handling and protection</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>3.         Tools, special tools, and equipment</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>4.         Verifying calibration/certification of instruments, tools, and equipment</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>5.         Required wiring checks using the troubleshooting procedures and charts</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>6.         Measurement and troubleshooting using meters</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>7.         LRU replacement general practices</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>B – WIRING PRACTICES DOCUMENTATION</p> <p>Know or demonstrate the construction and navigation of the applicable aeroplane wiring system overhaul or practices manual.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>8.         Standard wiring practices manual structure/overview</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>9.         Chapter cross-reference index</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>10.       Important data and tables</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>11.       Wiring diagram manuals</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>12.       Other documentation as applicable</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>C – INSPECTION</p> <p>Know the different types of inspections, human factors in inspections, zonal areas and typical damages.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>13.       General visual inspection (GVI), detailed inspection (DET), special detailed inspection (SDI), and zonal inspection, and their criteria and standards</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>14.       Human factors in inspection</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>15.       Zonal areas of inspection</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>16.       Wiring system damage</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>D – HOUSEKEEPING</p> <p>Know the contamination sources, materials, cleaning and protection procedures.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>17.       Aeroplane external contamination sources</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>18.       Aeroplane internal contamination sources</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>19.       Other contamination sources</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>20.       Contamination protection planning</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>21.       Protection during aeroplane maintenance and repair</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>22.       Cleaning processes</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="bottom" width="510"> <p>E – WIRE</p> <p>Know or demonstrate the correct identification of different wire types, their inspection criteria and damage tolerance, repair and preventative maintenance procedures.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>23.       Wire identification, type and construction</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>24.       Insulation qualities and damage limits</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>25.       Inspection criteria and standards for wire and wire bundles</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>26.       Wire bundle installation practices</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>27.       Typical damage and areas found (aeroplane specific)</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>28.       Maintenance and repair procedures</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>29.       Sleeving</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>30.       Unused wires - termination and storage</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>31.       Electrical bonding and grounds</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>F – CONNECTIVE DEVICES</p> <p>Know or demonstrate the procedures to identify, inspect, and find the correct repair for typical types of connective devices found on the applicable aeroplane.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>32.       General connector types and identification</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>33.       Cautions and protections</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>34.       Visual inspection procedures</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>35.       Typical damage found</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>36.       Repair procedures</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>G – CONNECTIVE DEVICE REPAIR</p> <p>Demonstrate the procedures for replacement of all parts of typical types of connectors found on the applicable aeroplane.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>37.       Circular connectors</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>38.       Rectangular connectors</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>39.       Terminal blocks - modular</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>40.       Terminal blocks - non-modular</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>41.       Grounding modules</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>42.       Pressure seals</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> </table> [Amdt 20/4] Appendix A to AMC 20-22 – EWIS Minimum Initial Training Programme for Group 1 and 2 ED Decision 2008/007/R Target Group 1: Qualified staff performing EWIS maintenance. Target Group 2: Qualified staff performing maintenance inspections on EWIS. <table border="1" cellpadding="0" cellspacing="0" width="604"> <tr> <td valign="top" width="510"> <p><b>TARGET GROUP</b></p> </td> <td valign="top" width="47"> <p><b>1</b></p> </td> <td valign="top" width="47"> <p><b>2</b></p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>A – GENERAL ELECTRICAL WIRING INTERCONNECTION SYSTEM PRACTICES</p> <p>Know or demonstrate safe handling of aeroplane electrical systems, line replaceable units (LRU), tooling, troubleshooting procedures, and electrical measurement.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>1.         Safety practices</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>2.         Electrostatic discharge sensitive (ESDS) device handling and protection</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>3.         Tools, special tools, and equipment</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>4.         Verifying calibration/certification of instruments, tools, and equipment</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>5.         Required wiring checks using the troubleshooting procedures and charts</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>6.         Measurement and troubleshooting using meters</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>7.         LRU replacement general practices</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>B – WIRING PRACTICES DOCUMENTATION</p> <p>Know or demonstrate the construction and navigation of the applicable aeroplane wiring system overhaul or practices manual.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>8.         Standard wiring practices manual structure/overview</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>9.         Chapter cross-reference index</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>10.       Important data and tables</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>11.       Wiring diagram manuals</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>12.       Other documentation as applicable</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>C – INSPECTION</p> <p>Know the different types of inspections, human factors in inspections, zonal areas and typical damages.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>13.       General visual inspection (GVI), detailed inspection (DET), special detailed inspection (SDI), and zonal inspection, and their criteria and standards</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>14.       Human factors in inspection</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>15.       Zonal areas of inspection</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>16.       Wiring system damage</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>D – HOUSEKEEPING</p> <p>Know the contamination sources, materials, cleaning and protection procedures.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>17.       Aeroplane external contamination sources</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>18.       Aeroplane internal contamination sources</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>19.       Other contamination sources</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>20.       Contamination protection planning</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>21.       Protection during aeroplane maintenance and repair</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>22.       Cleaning processes</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="bottom" width="510"> <p>E – WIRE</p> <p>Know or demonstrate the correct identification of different wire types, their inspection criteria and damage tolerance, repair and preventative maintenance procedures.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>23.       Wire identification, type and construction</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>24.       Insulation qualities and damage limits</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>25.       Inspection criteria and standards for wire and wire bundles</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>26.       Wire bundle installation practices</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>27.       Typical damage and areas found (aeroplane specific)</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>28.       Maintenance and repair procedures</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>29.       Sleeving</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>30.       Unused wires - termination and storage</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>31.       Electrical bonding and grounds</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>F – CONNECTIVE DEVICES</p> <p>Know or demonstrate the procedures to identify, inspect, and find the correct repair for typical types of connective devices found on the applicable aeroplane.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>32.       General connector types and identification</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>33.       Cautions and protections</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>34.       Visual inspection procedures</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>35.       Typical damage found</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="top" width="510"> <p>36.       Repair procedures</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> <p>X</p> </td> </tr> <tr> <td valign="bottom" width="510"> <p>G – CONNECTIVE DEVICE REPAIR</p> <p>Demonstrate the procedures for replacement of all parts of typical types of connectors found on the applicable aeroplane.</p> </td> <td valign="top" width="47"> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>37.       Circular connectors</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>38.       Rectangular connectors</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>39.       Terminal blocks - modular</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>40.       Terminal blocks - non-modular</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>41.       Grounding modules</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> <tr> <td valign="top" width="510"> <p>42.       Pressure seals</p> </td> <td valign="top" width="47"> <p>X</p> </td> <td valign="top" width="47"> </td> </tr> </table> [Amdt 20/4]