CS 26.60 Emergency landing - dynamic conditions

• ED Decision 2020/023/R found in: CS-26 Additional Airworthiness Specifications for Operations (No 2015/640) Part-26 (Mar 2023)

CS 26.60 Emergency landing – dynamic conditions ED Decision 2020/023/R Compliance with point [26.60](#_DxCrossRefBm881534099) of Part-26 is demonstrated by complying with CS 25.562 of CS-25, or its equivalent, or with the following (see [GM1 26.60](#_DxCrossRefBm881534097)): (a) Each seat type design that is approved for occupancy during taxiing, take-off, or landing must successfully complete dynamic tests or be demonstrated by rational analysis based on dynamic tests of a similar type seat, in accordance with each of the following emergency landing conditions. The tests must be conducted with an occupant simulated by a 77 kg (170 lb) anthropomorphic test dummy sitting in the normal upright position. The tests must include: (1) A change in the downward vertical velocity (Dv) of not less than 10.7 m/s (35 ft/s), with the aeroplane’s longitudinal axis canted downward at 30 degrees with respect to the horizontal plane, and with the wings level. The peak floor deceleration must occur in not more than 0.08 seconds after the impact, and reach a minimum of 14 g. (2) A change in the forward longitudinal velocity (Dv) of not less than 13.4 m/s (44 ft/s), with the aeroplane’s longitudinal axis horizontal and yawed by 10 degrees either to the right or the left, whichever would cause the greatest likelihood of the upper torso restraint system (if one is installed) moving off the occupant’s shoulder, and with the wings level. The peak floor deceleration must occur in not more than 0.09 seconds after the impact, and it must reach a minimum of 16 g. If floor rails or floor fittings are used to attach the seating devices to the test fixture, the rails or fittings must be misaligned with respect to the adjacent set of rails or fittings by at least 10 degrees vertically (i.e. away from being parallel), with one rolled by 10 degrees. (b) The following performance measures must not be exceeded during the dynamic tests that are conducted in accordance with subparagraph (a) of this paragraph: (1) If upper torso straps are used, the tension loads in the individual straps must not exceed 794 kg (1 750 lb). If dual straps are used to restrain the upper torso, the total strap tension loads must not exceed 907 kg (2 000 lb). (2) The maximum compressive load that is measured between the pelvis and the lumbar column of the anthropomorphic dummy must not exceed 680 kg (1 500 lb). (3) The upper torso restraint straps (if installed) must remain on the occupant’s shoulder during the impact. (4) The lap safety belt must remain on the occupant’s pelvis during the impact. (5) Each occupant must be protected from serious head injury under the conditions that are prescribed in sub-paragraph (a) of this paragraph. Where head contact with seats or other structure can occur, protection must be provided so that the head impact does not exceed a Head Injury Criterion (HIC) of 1 000 units. The level of HIC is defined by the equation —  Where — ‘t1’ is the initial integration time, ‘t2’ is the final integration time, and ‘a(t)’ is the total acceleration vs time curve for the head strike, and where ‘(t)’ is in seconds, and ‘(a)’ is in units of gravity (g). (6) Where leg injuries may result from contact with seats or other structures, protection must be provided to prevent axially compressive loads that exceed 1 021 kg (2 250 lb) in each femur. (7) The seat must remain attached at all points of attachment, although the structure may have yielded. (8) Seats must not yield under the tests that are specified in sub-paragraphs (a)(1) and (a)(2) of this paragraph to the extent that they would impede the rapid evacuation of the occupants of the aeroplane. [Issue: 26/3]